Stimmen - 0, Durchschnittliche Bewertung: 0
(
)
)
|
Anleitung Zusammenfassung
Zeolith drying The appliance features a Zeolith container Zeolith is a mineral which can store moisture and heat energy and release them again. During the washing step this heat energy is used to dry the mineral and heat up the rinsing water. During the drying phase moisture from the washing compartment is stored in the mineral and heat energy is released. This released heat energy is blown into the washing compartment with dry air. This accelerates and improves drying. These processes therefore save a great deal of energy. a=Warnings – Please ensure that the intake opening 1J is not obstructed and do not place any temperature-sensitive utensils in the lower basket at the rear right side above the blow opening 1R. en – Do not touch the blow opening 1R. The blow opening becomes hot and, furthermore, any damage will result in a chargeable callout by customer service. Switching on the appliance – Turn on the tap fully. – Open the door. – Switch on ON/OFF switch (. The display of the last selected programme flashes. This programme remains selected if no other programme button 0 is pressed. The expected programme duration flashes on the digital display 8. – Press the START button )". – Close the door. The programme starts running. Optical display while the programme is running * * depending on model While the programme is running, a light spot shines on the floor under the appliance door. Do not open the dishwasher door until the light point is no longer visible on the floor. If the appliance is installed at eye-level, with flush furniture front, the light point is not visible. This function can be changed as follows: – Open the door. – Switch on ON/OFF switch (. – Hold down programme button # and press START button )" until •:‹.... is indicated on the digital display. – Release both buttons. The LED for button # flashes and the digital display 8 displays the factory setting •:‹…. – Press programme button # until the factory set value ‚:‹‚ is indicated on the digital display 8. To change the setting: – By pressing the button 3, you can switch the function off ‚:‹‹ or on ‚:‹‚. – Press START button )". The set value is saved. – Close the door. en Remaining running time display When the programme is selected, the remaining running time of the programme is indicated on the digital display 8. The running time is determined during the programme by the water temperature, the number of utensils as well as the degree of soiling and may vary (depending on the selected programme). Timer programming You can delay the start of the programme in 1 hour steps up to 24 hours. – Open the door. – Switch on ON/OFF switch (. – Press the button ` + until ‹‚ is flaching in the timer programming display X. – Press + or – button until the ` displayed time corresponds with your requirements. – Press START button )", timer programming is activated. – To delete timer programming `, press the + or – button until ‹‹ is indicated on the digital display X. You can change your programme selection at any time until the programme starts. – Close the door. End of programme The programme has ended when the value ‹:‹‹ is indicated on the numerical display 8. The end of the programme is also indicated by an acoustic signal. This function can be changed as follows: – Open the door. – Switch on ON/OFF switch (. – Hold down programme button # and press START button )" until •:‹.... is indicated on the digital display. – Release both buttons. The LED for button # flashes and the digital display 8 displays the factory setting •:‹…. – Press programme button # until the factory set value ›:‹. is indicated on the digital display 8. To change the setting, – Press programme button 3. Each time the button is pressed, the set value increases by one level; when the value of ›:‹„ has been reached, the display jumps back to ›:‹‹ (off). – Press START button )", the set value is saved. – Close the door. en Automatic switch off after end of programme or interior light* * depending on model To save energy, the dishwasher can be automatically switched off 1 min or 120 min after the programme ends. The setting can be selected from .:‹‹ to .:‹.. .:‹‹ Appliance does not switch off automatically. The interior light 1" comes on when the door is opened irrespective of whether the ON/OFF switch ( is switched on or off. When the door is closed the light is off. If the door is open for l...
Dieses Handbuch ist für folgende Modelle:Geräte - S51T69X2EU/21 (1.82 mb)
Geräte - S51T69X2EU/22 (1.82 mb)
Geräte - S51T69X2EU/23 (1.82 mb)
Geräte - S51T69X2EU/25 (1.82 mb)