Stimmen - 0, Durchschnittliche Bewertung: 0
(
)
)
|
Anleitung Zusammenfassung
Optical display while the programme is running * * depending on model While the programme is running, a light spot shines on the floor under the appliance door. Do not open the dishwasher door until the light point is no longer visible on the floor. If the appliance is installed at eye-level, with flush furniture front, the light point is not visible. This function can be changed as follows: – Open the door. – Switch on ON/OFF switch (. – Hold down programme button # and press START button ` until •:‹.... is indicated on the digital display. – Release both buttons. The LED for button # flashes and the digital display h displays the factory setting •:‹…. – Press programme button # until the factory set value ‚:‹‚ is indicated on the digital display h. To change the setting: – By pressing the button 3, you can switch the function off ‚:‹‹ or on ‚:‹‚. – Press START button `. The set value is saved. – Close the door. The following applies to TurboSpeed 20 min.: During the heating up phase the light spot on the floor is lit constantly. At the end of the heating up phase the light spot flashes, indicating that the appliance can be opened and loaded. When the appliance has been restarted and the door closed, the light spot is lit constantly again during the rinsing phase. en Remaining running time display When the programme is selected, the remaining running time of the programme is indicated on the digital display h. The running time is determined during the programme by the water temperature, the number of utensils as well as the degree of soiling and may vary (depending on the selected programme). Timer programming * * depending on model You can delay the start of the programme in 1-hour steps up to 24 hours. – Open the door. – Switch on ON/OFF switch (. – Press button P + until the digital display h jumps to oe:‹‚. – Press P + or – button until the displayed time corresponds with your requirements. – Press START button `, timer programming is activated. – To delete timer programming, press the P + or – button until h oe:‹‹ is indicated on the digital display. You can change your programme selection at any time until the programme starts. – Close the door. End of programme The programme has ended when the value ‹:‹‹ is indicated on the numerical display h. The end of the programme is also indicated by an acoustic signal. This function can be changed as follows: – Open the door. – Switch on ON/OFF switch (. – Hold down programme button # and press START button ` until •:‹.... is indicated on the digital display. – Release both buttons. The LED for button # flashes and the digital display h displays the factory setting •:‹…. – Press programme button # until the factory set value ›:‹. is indicated on the digital display h. To change the setting, – Press programme button 3. Each time the button is pressed, the set value increases by one level; when the value of ›:‹„ has been reached, the display jumps back to ›:‹‹ (off). – Press START button `, the set value is saved. – Close the door. The following applies to TurboSpeed 20 min.: The programme has ended when you do not want to add another rinse cycle after the light spot on the floor has flashed and you switch off the appliance with the ON/ OFF switch (. en Automatic switch off after end of programme or interior light* * depending on model To save energy, the dishwasher can be automatically switched off 1 min or 120 min after the programme ends. The setting can be selected from .:‹‹ to .:‹.. .:‹‹ Appliance does not switch off automatically. The interior light 1" comes on when the door is opened irrespective of whether the ON/OFF switch ( is switched on or off. When the door is closed the light is off. If the door is open for longer than 60 min., the light switches off automatically. The interior light 1" is lit only when the set value .:‹‹ is selected. .:‹‚ Appliance switches off after 1 min. .:‹. Appliance switches off after 120 min. – Open the door. – Switch on ON/OFF switch (. – Hold down programme button # and press START button ` until •:‹... is indicated on the digital display. – Release both buttons. The LED for button # flashes and the digital display h displays the fac...
Dieses Handbuch ist für folgende Modelle:Geräte - S51M58X8EU/50 (1.83 mb)
Geräte - S51M58X8EU/51 (1.83 mb)
Geräte - S51M58X8EU/52 (1.83 mb)
Geräte - S51M58X8EU/55 (1.83 mb)