Stimmen - 0, Durchschnittliche Bewertung: 0
(
)
)
|
Anleitung Zusammenfassung
§ Half load * If you have only a few items to wash (e.g. glasses, cups, plates), you can switch to “half load”. This will save water, energy and time. It is recommended to put a little less detergent in the detergent dispenser than for a full load. · Hygiene * The temperature is increased during the cleaning process. This increases the hygiene status. This additional option is ideal for cleaning e.g. chopping boards and baby bottles. I Intensive zone * Perfect for a mixed load. You can wash very soiled pots and pans in the lower basket together with normally soiled utensils in the upper basket. The spray pressure in the lower basket is intensified, the rinsing temperature is increased slightly. . Extra drying * An increased temperature during the final rinse and an extended drying phase ensure that even plastic parts dry better. There is a slight increase in the energy consumption. 1 Operating the appliance Programme data The programme data (consumption values) can be found in the summary of instructions. They refer to normal conditions and the water hardness set value •:‹…. Different influencing factors such as e.g. water temperature or line pressure may result in deviations. Aqua sensor * * depending on model The Aqua sensor is an optical measuring device (light barrier) which measures the turbidity of the rinsing water. The Aqua sensor is used according to the programme. If the Aqua sensor is active, “clean” rinsing water can be transferred to the next rinse bath and water consumption can be reduced by 3–6 litres. If the turbidity is greater, the water is drained and is replaced with fresh water. In the automatic programmes the temperature and running time can also be adjusted to the degree of soiling. Operating the appliance en Switching on the appliance 1. Turn on the tap fully. 2. Switch on ON/OFF switch (. 3. Rotate programme selector 8 to the required programme. The expected programme duration flashes on the digital display H. 4. Press START button @. The programme starts running. Note -for environmentally friendly operation of the dishwasher: The Eco 50° programme is a particularly environmentally friendly programme. According to EU regulation 1016/2010 it is the “Standard programme” which is the most efficient standard cleaning cycle for cleaning normally soiled utensils in terms of the combined energy and water consumption for cleaning these types of utensils. Remaining running time display When the programme is selected, the remaining running time of the programme is indicated on the digital display H. The running time is determined during the programme by the water temperature, the number of utensils as well as the degree of soiling and may vary (depending on the selected programme). en Operating the appliance Timer programming * * depending on model You can delay the start of the programme in 1-hour steps up to 24 hours. 1. Close the door. 2. Switch on ON/OFF switch (. 3. Press button P until the digital display H jumps to oe:‹‚. 4. Press button P until the displayed time corresponds with your requirements. 5. Press START button @, timer programming is activated. 6. To delete the preselected starting time, press the button P until oe is indicated on the digital display. You can change your programme selection at any time until the programme starts. End of programme The programme has ended when the value ‹:‹‹ is indicated on the numerical display H. Switching off automatically after the end of the programme * * depending on model To save energy, the dishwasher is switched off 1 minute after the programme ends (factory setting). Automatic disconnection can be adjusted from .:‹‹ to .:‹.. .:‹‹ Appliance does not switch off automatically .:‹‚ Off after 1 min .:‹. Off after 120 min 1. Close the door. 2. Switch on ON/OFF switch (. 3. Press and hold down the START button @. 4. Rotate programme selector 8 until .:‹... s indicated on the digital display H. 5. Release button. The factory set value .:‹‚ is lit on the digital display H. To change the setting: 1. Rotate programme selector 8 until the required value is indicated on the digital display H. 2. Press START button @. The set value is saved. Switching off the appliance Short time after the end of the programme: 1. Switch off ON/OFF switch (. 2. Turn off the tap (not applicable if Aqua-Stop fitted). 3. Remove the utensils when they have cooled down. Note When the programme ends, leave the appliance to cool down a while before opening it. This will prevent steam from escaping and causing long- term damage to your built-in furniture. Operating the appliance en Interrupting the programme 1. Switch off ON/OFF switch (. The LEDs go out. The programme is saved. If the door was opened on an appliance which has a warm water connection or is heated, first leave the door ajar for several minutes and then close. Otherwise, expansion (pressure) may cause the appliance door to spring open or water to run out of the appliance. 2. To continue the programme, switc...
Dieses Handbuch ist für folgende Modelle:Geräte - S48E50N0EU/14 (1.44 mb)