Stimmen - 0, Durchschnittliche Bewertung: 0
(
)
)
|
Anleitung Zusammenfassung
Approx. 4 litres of water are required to regenerate the water softening system. As a result, the water consumption per rinse cycle increases by 0 to maximum 4 litres depending on the water hardness setting. Note If you use the detergent and rinse aid separately or switch from combined detergents to standard cleaning products, ensure that the rinse aid refill indicator has been switched on and the water softening system has been set to the correct water hardness. en Overview of programmes The max. possible number of programmes is illustrated in this overview. The corresponding programmes for your appliance can be found on the fascia. Delicate Type of dishes e.g. porcelain pans, cutlery, glasses, etc. Non- sensitive Mixed Mixed Type of food remnants e.g. Amount of food remnants State of food remnant Wash programme Soups, souffles, potatoes, pastries, rice, eggs, fried food Coffee, cake, milk, sausage, cold drinks, salads Soups, potatoes, pastries, rice, eggs, fried food Coffee, cake, milk, sausage, cold drinks, salads Rinse if the utensils have been left several washing in the dishwasher. days prior to LittleLarge Normal Very little High Lightly Adhesive Normal Low Auto 65–75. Auto 55–65. Auto 35–45. Eco 50. Quick 45. Prerinse Programme- sequence The programme sequence is optimised and adjusted according to the degree of soiling on the utensils. Dry Dry Clean 65 Interme- diate rinse Clean 50 Prerinse Clean 55 Interme- diate rinse Clean 45 Prerinse en Washing dishes Reduce costs! If only a small number of dishes have been loaded into the dishwasher, selecting a programme that operates at the next lowest temperature will usually suffice. Programme data The programme specifications can be found in the summary of instructions. Programme specifications refer to normal conditions. Greater deviations may occur due to: different amounts of dishes temperature of mains water supply pressure of mains water supply ambient temperature fluctuations in mains voltage machine-related factors (e.g. temperature, water volume, ...). Energy and water consumption is reduced by up to 1/4 when dishes are washed in the upper basket only. Water consumption values are based on a water hardness setting of 4. Aqua sensor * * some models The Aquasensor is an optical measuring device (light barrier) which measures the turbidity of the rinsing water. The Aqua sensor is used according to the programme. When the Aqua sensor is active, “clean” rinsing water may be transferred into the next rinsing bath and/or the temperature adjusted. If the turbidity is greater, the water is drained and is replaced with fresh water. In this way water consumption can be reduced by approx. 4 litres. Switching the dishwasher ON Turn on the tap. Set main switch 1 to ON. Indicators light up according to the last programme that was selected. This same programme will run again if no other programme button 7 is pressed The numerical display 9 shows the expected duration of the programme. Close door. The programme starts automatically. Optical indicator during operation * * With some models During the rinse programme a light point appears on the floor below the device’s door. Only open the dishwasher door when the light point has disappeared. In the case of built-in dishwashers with flush front the light point will not be visible. Remaining running time display When the appliance has started, the expected programme running time is displayed. The programmed running time is affected by the water temperature, the number of dishes, as well as the degree of soiling. If these conditions are changed, the running time (depending on the selected programme) can vary greatly. As the effect is not detected until a programme is running, the time may be longer or shorter than expected. Time delay * * on applicable models You can delay the start of the programme in 1-hour steps up to 19 hours. Switch on the appliance. Press the timer programming button 3 until the digital display 9 jumps to . Keep pressing the timer programming button until the required time is displayed. en To delete the timer programming, keep pressing the button until is displayed. You can change your programme selection at any time until the programme starts. End of programme The end of the programme is indicated by a buzzer. This function can be changed as follows:– Hold down Function button C pressed and switch on main switch , then let the buttons go. Function Button C flashes, and the digital display indicates the value which was set at the factory (semi-loud). To change the setting: Press Function button C . Each depression of the button increases the set value by one, when is reached, the display jumps back to (off). Switch off the main switch 1 . The set value is stored in the appliance. Switching the dishwasher OFF Several minutes after the programme has ended: Open the door when the programme has ended. Set main switch 1 to OFF. Turn the water tap off. (Does not apply when Aqua-Stop unit has been fitte...
Dieses Handbuch ist für folgende Modelle:Geräte - S44T59N0EU/10 (2.44 mb)