Stimmen - 0, Durchschnittliche Bewertung: 0 ( )

Hersteller: Bosch Dateigröße: 1.26 mb Dateiname: Unterrichtssprache:

Dieses Gerät hat auch andere Anweisungen:

Geräte - SRIKBH7/01 (1.24 mb)

Geräte - SRIKBH7/01 (1.27 mb)

– Switch on the main switch (. – Press the timer programming button until the digital display ` jumps to ‚oe. – Keep pressing the timer programming button until the required time is displayed. – To delete the preselected starting time, press the button until ‹oe is indicated on the digital display `. You can change your programme selection at any time until the programme starts. Washing the dishes Programme data The programme data (consumption values) can be found in the summary of instructions. They refer to normal conditions and the water hardness set value …. Different influencing factors such as water temperature or line pressure may result in deviations. Aqua sensor * * depending on model The Aqua sensor is an optical measuring device (light barrier) which measures the turbidity of the rinsing water. The Aqua sensor is used according to the programme. If the Aqua sensor is active, “clean” rinsing water can be transferred to the next rinse bath and water consumption can be reduced by 2–4 litres. If the turbidity is greater, the water is drained and is replaced with fresh water. In the automatic programmes the temperature and running time can also be adjusted to the degree of soiling. Switching on the appliance – Turn on the tap fully. – Close the door. – Rotate programme selector 8 to the required programme. – Switch on the main switch (. The expected programme duration is indicated on the numerical display `. – The programme starts running. Remaining running time display When the programme is selected, the remaining running time of the programme is indicated on the digital display `. The running time is determined during the programme by the water temperature, the number of utensils as well as the degree of soiling and may vary (depending on the selected programme). en End of programme The programme has ended when the value ‹ is indicated on the numerical display `. Switching off the appliance Short time after the end of the programme: – Switch off the main switch (. – Open the door. – Turn off the tap (not applicable if Aqua- Stop fitted). – Remove the utensils when they have cooled down. a=Warning At the end of the programme please open the door fully and not partially when emptying the dishwasher. Any escaping water vapour could damage sensitive worktops. Interrupting the programme – Switch off the main switch (. The LEDs go out. The programme is saved. If the door was opened on an appliance which has a warm water connection or is heated, first leave the door ajar for several minutes and then close. Otherwise, expansion (pressure) may cause the appliance door to spring open or water to run out of the appliance. – To continue the programme, switch on the main switch ( again. Terminating the programme (Reset) – Only when the main switch is on: Rotate programme selector 8 to the Reset position. The digital display ` indicates ‹ after approx. 3 sec. – The programme sequence lasts approx. 1 min. – Switch off the main switch (. Changing the programme After you have switched the appliance on, it is possible to change the programme within 2 min. If you want to change the programme afterwards, the appliance waits until the initiated programme section (e. g. washing) ends. The remaining time comprises the remaining time of the previous programme section and the remaining time of the new selected programme. Intensive drying The final rinse uses a higher temperature which improves the drying result. The running time may increase slightly. (Caution if utensils are delicate!) – Close the door. – Hold down button + and press main switch ( until the digital display illuminates. – Release both buttons. The factory-set value ‹ (off) or ‚ (on) is lit on the digital display `. To change the setting: – By pressing the button +, you can switch intensive drying on ‚ or off ‹. – Switch off the main switch (. The set value is saved. en Maintenance and care A regular inspection and maintenance of your machine will help to prevent faults. This saves time and prevents problems. Overall condition of the machine – Check spray arm for grease and limescale deposits. If you find such deposits: – Fill detergent dispenser with detergent. Start the appliance without utensils in the programme with the highest rinsing temperature. Clean the appliance with detergents/ appliance cleaners which are particularly suitable for use with dishwashers. – Regularly clean door seal with a damp cloth. Never use a steam cleaner to clean your dishwasher. The manufacturer is not liable for any consequential damage. Regularly wipe the front of the appliance and fascia with a damp cloth; water and a little washing up liquid are adequate. Do not use sponges with a rough surface or abrasive detergents, as these could scratch the surfaces. Stainless steel appliances: To prevent corrosion, avoid using sponge cloths or wash them out thoroughly several times before using for the first time. a=Warning Never use other chlorinated household detergents! Health haz...

Herunterladen

Geben Sie zwei Ziffern: