Stimmen - 1, Durchschnittliche Bewertung: 5
(
)
)
|
Anleitung Zusammenfassung
Programme TurboSpeed 20 min.: During the heating up phase • and the remaining running time are indicated alternately on the digital display; at the end p flashes, indicating that the appliance can be opened and loaded. When the appliance has been restarted, the remaining running time is indicated again during the rinsing phase. Timer programming * * depending on model You can delay the start of the programme in 1-hour steps up to 24 hours. 1. Close the door. 2. Switch on ON/OFF switch (. 3. Press button @ + until the digital display )" jumps to oe:‹‚. 4. Press @ + or – button until the displayed time corresponds with your requirements. 5. Press START button P, timer programming is activated. 6. To delete timer programming, press the @ + or – button until )" oe:‹‹ is indicated on the digital display. You can change your programme selection at any time until the programme starts. End of programme The programme has ended when the value ‹:‹‹ is indicated on the numerical display )". The following applies to TurboSpeed 20 min.: As soon as ‹:‹‹ is indicated on the digital display )", the rinse cycle has ended. When the appliance door has been opened, p is indicated on the digital display. If no further rinse cycle is required, switch off the appliance with the ON/OFF switch (. en Operating the appliance Switching off automatically after the end of the programme * * depending on model To save energy, the dishwasher is switched off 1 minute after the programme ends (factory setting). Automatic disconnection can be adjusted from .:‹‹ to .:‹.. .:‹‹ Appliance does not switch off automatically .:‹‚ Off after 1 min .:‹. Off after 120 min 1. Close the door. 2. Switch on ON/OFF switch (. 3. Hold down programme button # and press START button P until •:‹... is indicated on the digital display. 4. Release both buttons. The LED for button # flashes and the digital display )" displays the factory setting •:‹…. 5. Press programme button # until the factory set value .:‹‚ is indicated on the digital display )". To change the setting: 1. Press programme button 3. Each time the button is pressed, the set value increases by one level; when the value of .:‹. has been reached, the display jumps back to .:‹‹ (off). 2. Press START button P. The set value is saved. Switching off the appliance Short time after the end of the programme: 1. Switch off ON/OFF switch (. 2. Turn off the tap (not applicable if Aqua-Stop fitted). 3. Remove the utensils when they have cooled down. Note When the programme ends, leave the appliance to cool down a while before opening it. This will prevent steam from escaping and causing long- term damage to your built-in furniture. In the case of the TurboSpeed 20 min. programme switch off if no further rinse cycle is to follow. Interrupting the programme 1. Switch off ON/OFF switch (. The LEDs go out. The programme is saved. If the door was opened on an appliance which has a warm water connection or is heated, first leave the door ajar for several minutes and then close. Otherwise, expansion (pressure) may cause the appliance door to spring open or water to run out of the appliance. 2. To continue the programme, switch on the ON/OFF switch ( again. Operating the appliance en Terminating the programme (Reset) 1. Press START button P for approx. 3 sec. The numerical display )" indicates ‹:‹‚. 2. The programme sequence lasts approx. 1 min. On the digital display )" is indicated ‹:‹‹. 3. Switch off ON/OFF switch (. Changing the programme When the START button P has been pressed, the programme cannot be changed. The only way a programme can be changed is by Cancel programme (Reset). Intensive drying The final rinse uses a higher temperature which improves the drying result. The running time may increase slightly. (Caution if utensils are delicate!) 1. Close the door. 2. Switch on ON/OFF switch (. 3. Hold down programme button # and press START button P until the digital display )" •:‹... is indicated. 4. Release both buttons. The LED for button # flashes and the digital display )" displays the factory setting •:‹…. 5. Press programme button # until the factory set value s:‹‹ is indicated on the digital display )". To change the setting, 1. Press the button 3 to switch the Intensive drying on s:‹‚ or off s:‹‹. 2. Press START button P. The set value is saved. en Cleaning and maintenance 2 Cleaning and maintenance A regular inspection and maintenance of your machine will help to prevent faults. This saves time and prevents problems. Overall condition of the machine . Check spray arm for grease and limescale deposits. If you find such deposits: . Fill detergent dispenser with detergent. Start the appliance without utensils in the programme with the highest rinsing temperature. Clean the appliance with detergents/ appliance cleaners which are particularly suitable for use with dishwashers. . To ensure that the door seal always remains clean and hygienic, regularly clean it with a damp cloth and a little washing-up liquid....
Dieses Handbuch ist für folgende Modelle:Geräte - SPI53M55EU/14 (1.62 mb)
Geräte - SPS53M52EU/01 (1.62 mb)
Geräte - SPS53M52EU/14 (1.62 mb)
Geräte - SPS53M58EU/01 (1.62 mb)