Stimmen - 0, Durchschnittliche Bewertung: 0
(
)
)
|
Anleitung Zusammenfassung
Close the door. 2. Switch on ON/OFF switch (. 3. Hold down programme button # and press START button P until •:‹... is indicated on the digital display. 4. Release both buttons. The LED for button # flashes and the digital display )" displays the factory setting •:‹…. 5. Press programme button # until the factory set value .:‹‚ is indicated on the digital display )". en Operating the appliance To change the setting: 1. Press programme button 3. Each time the button is pressed, the set value increases by one level; when the value of .:‹. has been reached, the display jumps back to .:‹‹ (off). 2. Press START button P. The set value is saved. Switching off the appliance Short time after the end of the programme: 1. Switch off ON/OFF switch (. 2. Turn off the tap (not applicable if Aqua-Stop fitted). 3. Remove the utensils when they have cooled down. Note When the programme ends, leave the appliance to cool down a while before opening it. This will prevent steam from escaping and causing long- term damage to your built-in furniture. Interrupting the programme 1. Switch off ON/OFF switch (. The LEDs go out. The programme is saved. If the door was opened on an appliance which has a warm water connection or is heated, first leave the door ajar for several minutes and then close. Otherwise, expansion (pressure) may cause the appliance door to spring open or water to run out of the appliance. 2. To continue the programme, switch on the ON/OFF switch ( again. Terminating the programme (Reset) 1. Press START button P for approx. 3 sec. The numerical display )" indicates ‹:‹‚. 2. The programme sequence lasts approx. 1 min. On the digital display )" is indicated ‹:‹‹. 3. Switch off ON/OFF switch (. Changing the programme When the START button P has been pressed, the programme cannot be changed. The only way a programme can be changed is by Cancel programme (Reset). Intensive drying The final rinse uses a higher temperature which improves the drying result. The running time may increase slightly. (Caution if utensils are delicate!) 1. Close the door. 2. Switch on ON/OFF switch (. 3. Hold down programme button # and press START button P until the digital display )" •:‹... is indicated. 4. Release both buttons. The LED for button # flashes and the digital display )" displays the factory setting •:‹…. 5. Press programme button # until the factory set value s:‹‹ is indicated on the digital display )". To change the setting, 1. Press the button 3 to switch the Intensive drying on s:‹‚ or off s:‹‹. 2. Press START button P. The set value is saved. 2 Cleaning and maintenance A regular inspection and maintenance of your machine will help to prevent faults. This saves time and prevents problems. Cleaning and maintenance en Overall condition of the machine . Check spray arm for grease and limescale deposits. If you find such deposits: . Fill detergent dispenser with detergent. Start the appliance without utensils in the programme with the highest rinsing temperature. Clean the appliance with detergents/ appliance cleaners which are particularly suitable for use with dishwashers. . To ensure that the door seal always remains clean and hygienic, regularly clean it with a damp cloth and a little washing-up liquid. . If the appliance is switched off for a prolonged period, leave the door ajar to prevent the formation of an unpleasant odour. Never use a steam cleaner to clean your dishwasher. The manufacturer is not liable for any consequential damage. Regularly wipe the front of the appliance and fascia with a damp cloth; water and a little washing up liquid are adequate. Do not use sponges with a rough surface or abrasive detergents, as these could scratch the surfaces. Stainless steel appliances: To prevent corrosion, avoid using sponge cloths or wash them out thoroughly several times before using for the first time. a Warning – Health hazard Never use other domestic detergents, e.g. containing chlorine! Special salt and rinse aid . Check the refill indicators ` and h. If required, refill salt and/or rinse aid. en Cleaning and maintenance Filters The filters 1R keep large foreign objects in the rinsing water away from the pump. These foreign objects may occasionally block the filters. The filter system consists of a coarse filter, a flat fine filter and a microfilter. 1. After each washing cycle check the filters for residue. 2. Unscrew filter cylinder as illustrated and take out filter system. Spray arms Limescale and contaminants in the rinsing water may block nozzles and bearings on the spray arms 1: and 1B. 1. Check outlet nozzles on the spray arms for blockages. 2. Unscrew the upper spray arm 1:. 3. Remove the lower spray arm 1B upwards. 3.Remove any residue and clean filters under running water. 4.Re-install filter system in reverse sequence and ensure that the arrow marks are opposite each other after closing the filter system. 4.Clean spray arms under running water. 5.Re-engage or screw on spray arms. Fault, what to do? en 3...
Dieses Handbuch ist für folgende Modelle:Geräte - SN25M231TR/12 (1.78 mb)
Geräte - SN25M239EU/61 (1.78 mb)
Geräte - SN25M239EU/73 (1.78 mb)
Geräte - SN55L531EU/09 (1.78 mb)