Stimmen - 1, Durchschnittliche Bewertung: 5 ( )

Hersteller: Bosch Dateigröße: 2.25 mb Dateiname: Unterrichtssprache:

a Warning – Risk of injury! Do not touch the blow opening 1R. The blow opening becomes hot and, furthermore, any damage will result in a chargeable callout by customer service. Operating the appliance en Switching on the appliance 1. Turn on the tap fully. 2. Switch on ON/OFF switch (. The Eco 50° programme display flashes. This programme remains selected if no other programme button 0 is pressed. The expected programme duration flashes on the digital display )*. 3. Press the START button h. The programme starts running. Note -for environmentally friendly operation of the dishwasher: For ecological reasons the Eco 50° programme is preset whenever the appliance starts. This conserves environmental resources and not least saves you money. The Eco 50° programme is a particularly environmentally friendly programme. According to EU regulation 1016/2010 it is the “Standard programme” which is the most efficient standard cleaning cycle for cleaning normally soiled utensils in terms of the combined energy and water consumption for cleaning these types of utensils. Programme sequence indicator )" Your dishes are being -/, cleaned. 5/% Your dishes are being rinsed. Your dishes are being dried. =/< Remaining running time display When the programme is selected, the remaining running time of the programme is indicated on the digital display )*. The running time is determined during the programme by the water temperature, the number of utensils as well as the degree of soiling and may vary (depending on the selected programme). Timer programming * * depending on model You can delay the start of the programme in 1-hour steps up to 24 hours. 1. Close the door. 2. Switch on ON/OFF switch (. 3. Press button X + until the digital display )* jumps to oe:‹‚. 4. Press X + or – button until the displayed time corresponds with your requirements. 5. Press START button h, timer programming is activated. 6. To delete timer programming, press the X + or – button until )* oe:‹‹ is indicated on the digital display. You can change your programme selection at any time until the programme starts. en Operating the appliance End of programme The programme has ended when the value ‹:‹‹ is indicated on the numerical display )*. Automatic switch off after end of programme or interior light* * depending on model To save energy, the dishwasher can be automatically switched off 1 min or 120 min after the programme ends. The setting can be selected from .:‹‹ to .:‹.. .:‹‹ Appliance does not switch off automatically. The interior light 1" comes on when the door is opened irrespective of whether the ON/OFF switch ( is switched on or off. When the door is closed the light is off. If the door is open for longer than 60 min., the light switches off automatically. The interior light 1" is lit only when the set value .:‹‹ is selected. .:‹‚ Appliance switches off after 1 min. .:‹. Appliance switches off after 120 min. 1. Close the door. 2. Switch on ON/OFF switch (. 3. Hold down programme button # and press START button h until •:‹... is indicated on the digital display. 4. Release both buttons. The LED for button # flashes and the digital display )* displays the factory setting •:‹…. 5. Keep pressing programme button # until the value .:‹... is indicated on the numerical display )*. To change the setting: 1. Press programme button 3. Each time the button is pressed, the set value increases by one level; when the value of .:‹. has been reached, the display jumps back to .:‹‹. 2. Press START button h. The set value is saved. Switching off the appliance Short time after the end of the programme: 1. Switch off ON/OFF switch (. 2. Turn off the tap (not applicable if Aqua-Stop fitted). 3. Remove the utensils when they have cooled down. Note When the programme ends, leave the appliance to cool down a while before opening it. This will prevent steam from escaping and causing long- term damage to your built-in furniture. Operating the appliance en Interrupting the programme 1. Switch off ON/OFF switch (. The LEDs go out. The programme is saved. If the door was opened on an appliance which has a warm water connection or is heated, first leave the door ajar for several minutes and then close. Otherwise, expansion (pressure) may cause the appliance door to spring open or water to run out of the appliance. 2. To continue the programme, switch on the ON/OFF switch ( again. Terminating the programme (Reset) 1. Press START button h for approx. 3 sec. The numerical display )* indicates ‹:‹‚. 2. The programme sequence lasts approx. 1 min. On the digital display )* is indicated ‹:‹‹. 3. Switch off ON/OFF switch (. Changing the programme When the START button h has been pressed, the programme cannot be changed. The only way a programme can be changed is by Cancel programme (Reset). Intensive drying The final rinse uses a higher temperature which improves the drying result. The running time may increase slightly. (Caution if utensils are delicate!) 1. Close the door. 2. Switc...

Herunterladen

Geben Sie zwei Ziffern: