Stimmen - 0, Durchschnittliche Bewertung: 0
(
)
)
|
Anleitung Zusammenfassung
Refill with special salt. Sensor does not detect salt tablets. Use different special salt. Refill indicator for salt h and/or rinse-aid ` is not lit. Refill indicator switched off. There is still enough special salt/ rinse aid available. Activation/deactivation (see chapter Water softening system/Special salt or Rinse aid). Check refill indicator, levels. Water is left in the appliance at the end of the programme. Filter system or area under the filters 1R is blocked. The programme has not yet ended. Clean filters and area underneath (see Waste water pump). Wait until programme ends or reset (see Terminating the programme). en Fault, what to do? Fault Cause Remedial action Utensils not dry. No or too little rinse aid in the dispenser. Programme selected without drying. Water collecting in depressions on the utensils and cutlery. The combined detergent used has a poor drying performance. Refill rinse aid. Select programme with drying (see Overview of programmes, Programme sequence). Arrange utensils in a sloping position, arrange affected utensils as sloping as possible. Use different combination detergent with better drying performance. Use of rinse aid also increases the drying performance. Intensive drying to increase drying not activated. Utensils were removed too early or drying process had not ended yet. The eco rinse aid used has a poor drying performance. Activate intensive drying (see Operating the appliance) Wait until program ends or wait until 30 min after program ends before removing utensils. Use a proprietary rinse aid. Eco products are much less effective. Plastic utensils not dry. Special properties of plastic. Plastic has a lower heat storage capacity and therefore dries less well. Cutlery not dry. Cutlery not arranged properly in the cutlery basket. Cutlery not arranged properly in the cutlery drawer. Separate cutlery if possible, prevent contact points. Arrange cutlery properly and separate if possible. Appliance interior wet after rinse cycle. No appliance fault. On account of the “Condensation drying” principle, water droplets are physically induced and required in the container. The humidity in the air condenses on the inner walls of the dishwasher, drains and is pumped out. Fault, what to do? en Fault Cause Remedial action Food remnants Utensils placed too closely Arrange utensils with adequate clearance on the utensils. together, utensils basket between them ensuring that the spray jets overfilled. can reach the surface of the utensils. Prevent contact points. Spray arm rotation obstructed. Arrange utensils so that the spray arm can rotate without obstruction. Spray arm nozzles blocked. Clean the spray arm nozzles, (See Cleaning and maintenance). Filters 1R dirty. Clean filters, (see Cleaning and maintenance). Filters 1R inserted incorrectly Insert and engage filters correctly. and/or not engaged. Rinse programme too weak. Select a more intensive rinse programme. Utensils precleaned too intensely; Do not prerinse utensils. Remove only large sensors therefore decide on food remnants. weak programme sequence. Stubborn soiling cannot be Recommended programme Eco 50° or Intensive. completely removed. Tall narrow receptacles in corner Do not place hollow receptacles too areas are not rinsed adequately. obliquely and do not place in the corner area. Top basket 1* on right and left Set top basket to same height using side not set to same height. levers. Detergent residue Detergent dispenser cover Detergent dispenser cover must not be blocked by utensils and therefore obstructed by utensils. does not open fully. Do not place utensils or fragrance dispenser in the tablet collecting tray. Detergent dispenser cover Tablet must be inserted flat and not upright. blocked by the tablet. Tablets used in the quick or short Dissolving time of tablets too long for programme. a quick or short programme. Dissolving time of the detergent Use a detergent powder or select a more is not reached in the selected intensive programme. short programme. Washing effect and dissolving Change detergent. performance are reduced after a prolonged storage time or detergent is very lumpy. en Fault, what to do? Fault Cause Remedial action Water stains on plastic Droplet formation on plastic Use a more intensive programme (more parts surface is physically unavoidable. water changes). After drying, water stains are visible. Arrange utensils in a sloping position. Use rinse aid. If required, increase softening setting. Washable or water-soluble Detergent substances are Change detergent brand. coatings in the container or on the door. deposited. These coatings cannot usually be removed with Clean appliance mechanically. chemicals (appliance cleaner, ...). If there is a “white coating” on Increase softening setting and change the container floor, the water detergent if required. softening system has been set marginally. Salt dispenser cover 1J not Close salt dispenser cover correctly. closed. Only for glasses: Initial glass Se...
Dieses Handbuch ist für folgende Modelle:Geräte - SMS57E28EU/73 (1.97 mb)