Stimmen - 0, Durchschnittliche Bewertung: 0
(
)
)
|
Anleitung Zusammenfassung
There are currently several types of combined detergent products available. 2in1: They contain detergent and rinse aid or salt function. 3in1: They contain detergent, rinse aid and salt function. 4in1: They contain a detergent, rinse-aid, salt function and an additional glass protection component. In addition, other combined products with a comparable effect are offered according to the manufacturer. >>> Always check the type of detergent or combined product which you are using! Always follow the operating instructions or the information on the packaging. The rinse programme is automatically adjusted in order to obtain the best possible rinsing and drying result. Observe the following important information if using combined cleaning products: Regeneration salt is not required up to a water hardness of 21 dH (37 fH, 26 Clarke, 3.7 mmol/l) only. No other settings on the appliance are required. If in doubt, please contact the detergent manufacturer, especially if: the utensils are very wet at the end of the programme. limescale forms. Note Optimum rinsing and drying results can be obtained by using standard detergents in conjunction with separate application of rinse aid. Observance of the operating instructions or information on the packaging of the combined detergents determines their effectiveness. Note Even if the rinse aid refill indicator is lit, the rinse programme runs correctly when 3in1 products are used. If the rinse aid refill indicator 5 is defective and you would like to switch it off, proceed as follows: Switching the rinse aid refill indicator off and on You can switch the rinse aid refill indicator 5 on or off. This function can be changed as follows. Hold down the programme button and press the main switch 1 until the digital display lights up, then release the buttons. 8 is indicated on the digital display (rinse aid refill indicator on). By pressing the programme button 3 , you can switch off or switch on the rinse aid indicator. Switch off the main switch 1 ; the setting is saved. Note If you use the detergent and rinse aid separately or switch from combined detergents to standard cleaning products, ensure that the rinse aid refill indicator has been switched on. aus Overview of programmes The max. possible number of programmes is illustrated in this overview. The corresponding programmes for your appliance can be found on the fascia. Rinse if the utensils have been left several days prior to washing in the dishwasher. Coffee, cake, milk, sausage, cold drinks, salads Soups, souffles, potatoes, pastries, rice, eggs, fried food Type of dishes e.g. porcelain pans, cutlery, glasses, etc. Type of food remnants e.g. Programme- sequence The programme sequence is optimised and adjusted according to the degree of soiling on the utensils. Dry Dry Rinse-aid 45 Intermediate rinse Wash 45 Prerinse Rinse-aid 55 Intermediate rinse Wash 45 Prerinse Non- delicate Mixed Wash programme Very little LittleLarge High NormalLightly Adhesive Amount of food remnants State of food remnant Auto 65–75 Auto 55–65 Auto 35–45 Normal 45 Quick 45 Prerinse Low Normal 105-135 1,45-1,75 12-20 30 0,80 – – 10 20 0,05 4 – 85-140 1,00-1,60 – 9-19 140 0,60 – 13,7 80-90 0,80-0,90 – 13-18 Programme details Laboratory measured value in accordance with AS/NZS 2007 Duration in minutes Electricity consumption in kWh Water consumption in litres with Aquasensor Normal / Delicate Coffee, cake, milk, sausage, cold drinks, salads Soups, potatoes, pastries, rice, eggs, fried food Mixed aus Washing dishes Reduce costs! If only a small number of dishes have been loaded into the dishwasher, selecting a programme that operates at the next lowest temperature will usually suffice. Programme data The stated programme data are based on standard operating conditions. The values can vary considerably according to: different amounts of dishes temperature of mains water supply pressure of mains water supply ambient temperature fluctuations in mains voltage machine-related factors (e.g. temperature, water volume, ...). Aqua sensor * * some models The Aquasensor is an optical measuring device (light barrier) which measures the turbidity of the rinsing water. The Aqua sensor is used according to the programme. When the Aqua sensor is active, “clean” rinsing water may be transferred into the next rinsing bath and/or the temperature adjusted. If the turbidity is greater, the water is drained and is replaced with fresh water. In this way water consumption can be reduced by approx. 4 litres. Switching the dishwasher ON Turn on the tap. Set main switch 1 to ON. Indicators light up according to the last programme that was selected. This same programme will run again if no other programme button 6 is pressed The numerical display 8 shows the expected duration of the programme. Close door. The programme starts automatically. Optical indicator during operation * * With some models During the rinse programme a light point appears on the floor below the device’s door...
Dieses Handbuch ist für folgende Modelle:Geräte - SL56T590AU/13 (2.51 mb)
Geräte - SL56T590AU/18 (2.51 mb)