Stimmen - 0, Durchschnittliche Bewertung: 0
(
)
)
|
Anleitung Zusammenfassung
Pull out the mains plug or switch off the fuse. Turn off the tap, call customer service. Disposal – Make redundant appliances unusable to prevent subsequent accidents. – Dispose of the appliance in an environmentally friendly manner. m Warning Children could become locked in the appliance (risk of suffocation) or find themselves in other dangerous situations. Therefore: Pull out the mains plug, sever and dispose of the power cord. Destroy the door lock so that the door can no longer be closed. en Getting to know your appliance Diagrams of the control panel and the interior of the appliance can be found in the envelope at the front. Individual positions are referred to in the text. Control panel ( ON/OFF switch 0 Programme selector 8 START button @ Timer programming * H Additional options ** P Rinse aid refill indicator X Salt refill indicator ‘ Display .Check water supply. h Dry display )" Cleaning display * depending on model ** Number depending on model Appliance interior 1" Spray arm 1* Filters 12 Dispenser for special salt 1: Cutlery basket 1B Basket 1J Dispenser for rinse aid 1R Detergent dispenser 1Z Lock for detergent dispenser 1b Rating plate en Water softening system To ensure good washing results, the dishwasher requires soft water, i.e. containing low amounts of lime, otherwise white limescale will be deposited on the utensils and inner container. Tap water above a specific degree of water hardness must be softened, i.e. descaled, for use in a dishwasher. Water is softened with special salt in the water softening system of the dishwasher. The setting and therefore the required amount of salt depends on the degree of hardness of your tap water (see table). Water hardness table Setting The amount of salt dispensed can be set in 4 stages depending on the hardness of your water. Accordingly 0, 1, 2 or 3 displays are lit (see table). Factory setting: 1. – Find out about the hardness value of your tap water. Your water utility company will help you with this. – Setting can be found in the water hardness table. – Close the door. – Switch on ON/OFF switch (. The Cleaning display )" flashes. – Press and hold down the START button 8. – Rotate programme selector 0 until the salt refill indicator X flashes. – Release button. The salt refill indicator X flashes and the display .Check water supply. ‘ are lit (= Setting 1). To change the setting: – Rotate programme selector 0 until the required setting has been selected. – Press START button 8. The salt refill indicator X goes out. The selected setting is saved. . . . !. . . . . . . . . en Special salt $ Using special salt Always refill with special salt immediately before switching on the appliance. This ensures that overrun special salt solution is immediately washed out and does not corrode the rinsing tank. – Open the screw-type cap of the compartment 12. – Fill the tank with water (only required when switching on the appliance for the first time). – Then add dishwasher salt (not table salt or tablets). The water is displaced and runs out. As soon as the salt refill indicator X on the fascia is lit, top up the salt. * depending on model Using detergents with salt component Dre eeet ttwtslcmon nn gia o pt nh e s t If combined detergents with a salt component are used, salt can usually be omitted up to a water hardness of 21° dH (37° fH, 26° Clarke, 3.7 mmol/l). If the water hardness is over 21° dH, special salt must be used. e mgoen nnyt ttisf fsssftoaewri iiSthnfwcg Switching off salt refill indicator/ water softening system If the salt refill indicator X is impaired (e.g. when using combined detergents containing salt component), it can be switched off. – Proceed as described under .Adjusting the water softening system. and select setting 0. The water softening system and salt refill indicator are now switched off. n Caution Never fill the salt dispenser with detergent. You will destroy the water softening system. en Rinse aid % As soon as the rinse-aid refill indicator P is lit on the fascia, there is still a rinse-aid reserve of 1 . 2 rinsing processes. Refill with rinse aid. The rinse aid is required for stain-free utensils and clear glasses. Use only rinse aid for domestic dishwashers. Combined detergents with rinse-aid component may be used up to a water hardness of 21° dH (37° fH, 26° Clarke, 3.7 mmol/l) only. If the water hardness is over 21° dH, rinse aid must be used. – Open the dispenser 1J by pressing and lifting the plate on the cover. . Carefully pour rinse aid up to the max. mark in the filler opening. .Close cover until it clicks shut. .To prevent excessive foam formation during the next rinse cycle, remove any rinse aid which has run over with a cloth. Setting amount of rinse aid The amount of rinse aid dispensed can be set in 4 stages. Accordingly 0, 1, 2 or 3 displays are lit (see water hardness table). Factory setting: 2. Do not change the amount of rinse aid unless streaks (select lower setting) or water stains (select high...
Dieses Handbuch ist für folgende Modelle:Geräte - SK23E800TI/08 (2.19 mb)