Stimmen - 0, Durchschnittliche Bewertung: 0
(
)
)
|
Anleitung Zusammenfassung
By pressing the button + 3 you enrol the device again at the gateway. After successfully enrolling the device the message “Auto Wash” will be displayed. If the enrolment is unsuccessful the display shows “no gateway found”. ** Only with installed interface Aqua sensor * * on applicable models The Aqua sensor is an optical measuring device which measures the turbidity of the rinsing water. A light barrier can detect dissolved food remnants in the water, e.g. egg, fat and oats. The Aqua sensor is used according to the programme. When the Aqua sensor is active, ”clean” rinsing water may be transferred into the next rinsing bath and/or the temperature adjusted. If the turbidity is greater, the water is drained and is replaced with fresh water. In this way the water consumption is reduced by approx. 4 litres for utensils which are ”less” dirty. Optical indicator during operation * * With some models During the rinse programme a light point appears on the floor below the device’s door. Only open the dishwasher door when the light point has disappeared. In the case of built-in dishwashers with flush front the light point will not be visible. Start programme Before starting check again whether the spray arms can move freely. Press the button “Start” 5 in the Main Menu. The message “Close the door” will be displayed, alternating with a display of the expected programme time. This time is only approximate. At programme start it corresponds to the time the programme ran the last time. During the programme run the remaining time will be adjusted according to the water supply temperature and the amount and soil level of the dishes. If you have chosen a time for the programme start the message “Close Door” will appear when the programme is started, alternating with the pre-selected time. Close the door. The programme or the pre-selected time respectively will run. The programme and other settings can still be changed as long as the door is still open after pressing the button “Start” 5 . By pressing the button M/OK 2 “Back”, return to the Main Menu where you can change the settings. Finally start the programme again. When the door is closed after the start and the programme has already started, you will have to interrupt the programme in order to change any settings (see “Cancel Programme”). Cancel Programme In order to interrupt the programme, open the door. In order to avoid water escaping, only open the door slightly first. The message “Cancel Programme” will be displayed, alternating with the message “Close the door”, the remaining programme time, the selected programme, and the current programme phase. In order to interrupt, do not in any circumstance press the button – 3 “Cancel Programme” because this will not allow the programme to continue! To continue the programme, close the door. The programme will continue automatically. In the case of a warm water supply or when the appliance is already heated, leave the door slightly ajar for a few minutes before closing it. Otherwise the door can spring open again due to the warm air trapped in the device’s interior. Cancelling active programme Open the door. First open the door only slightly in order to avoid water spraying out. The message “Cancel Programme” will be displayed, alternating with the message “Close the door”, the remaining programme time, the selected programme, and the current programme phase. In order to cancel the programme, press – 3 “Cancel Programme”. The display shows “To drain Close the door” with the message “Close the door” flashing. en Close the door. The water remaining in the device’s interior will be pumped off. Once the pumping off has finished a buzzer will sound 5 times. Open the door. “Ready” is briefly displayed, the appliance automatically switches off after 5 seconds. End of the programme As soon as the programme has finished a buzzer will sound 5 times. Open the door. “Ready” is briefly displayed, the appliance automatically switches off after 5 seconds. If the door is not opened, the appliance automatically switches off after one hour. During this time the acoustic signal sounds every 15 minutes. After letting the device cool down take out the dishes. When the programme has finished you can switch off the appliance or start it again. Note For an optimum drying of the dishes wait for 15 minutes after the programme has finished before you open the door and empty the dishwasher. During this time the possibly remaining water on the dishes can evaporate and condense on the sides of the device’s interior. Note If the device becomes disconnected from the power supply during operation (e.g. it is switched off or there is a power cut), all settings remain stored. Operation will resume automatically once the power supply has been restored. en Maintenance and care You can help prevent faults by checking and maintaining your appliance regularly. This will save time and reduce problems. Therefore you should occasionally examine the inside of your...
Dieses Handbuch ist für folgende Modelle:Geräte - SGVATR1/03 (1.64 mb)
Geräte - SHVATR1/01 (1.64 mb)
Geräte - SHVATR1/03 (1.64 mb)