To change the setting, press programme button B . Each time the button is pressed, the set value increases by 1; after , the setting goes back to . Switch off the main switch 1 . The chosen setting has now been stored. Approx. 4 litres of water are required for regenerating the water softening system. The overall water consumption per load can therefore be increased by between 0 and a maximum of 4 litres according to the water hardness setting. en Filling the salt dispenser Salt must always be filled before the appliance is switched on, so that excess salt solution is immediately flushed away to prevent corrosion. Open the screw-type cap of the compartment 24 . Before using the appliance for the first time, pour about 1 litre of water in the salt container. Then refill with salt (not cooking salt) until the salt container is full (max. 1.5 kg). When you refill the salt, water is being displaced and drains off. Salt refill indicator As soon as the salt refill indicator 5 is lit on the control panel, refill with salt immediately before the next rinse cycle. Depending on the washing frequency and the hardness setting, the regeneration salt may not have to be topped up for several months. The LOW SALT indicator 5 on the front panel will light up initially but will extinguish again after a short period when the salt solution has become sufficiently concentrated. When the control is set to , it is not necessary to fill up with salt as none will be consumed while the dishwasher is operating. The LOW SALT indicator is switched off. If the control is set between and , then salt must be added to the dispenser. Warning Do not pour detergent into the container for special salt. This would destroy the water softener. en Adding rinse aid Rinse aid is used in the rinsing cycle to ensure clear glasses and stain-free utensils. Open the lid of the rinse-aid dispenser 29 by pressing the button on the rinse-aid lid and lifting up the lid. Pour the rinse-aid into the filler hole until the level indicator turns dark. Close the lid, ensuring that you hear it snap closed. rinse–aid control Use only rinse aid for domestic dishwashers. Spilt rinse aid may result in excessive foam formation in the next rinse cycle. Therefore, remove any spilt rinse aid with a cloth. Convenient rinse-aid filling procedure with half-open door Open the rinse-aid lid and pull out the hinged filling aid until it locks into position. Slowly fill with rinse aid but do not overfill. Close the rinse-aid lid until it clicks shut. Set Amount of Rinse Aid The amount of rinse aid is set at the factory to 4. Only change this setting if streaks or water stains remain on the dishes. Hold the Programme button 3 and press the main switch 1 . Release both buttons. In order to change the setting, press the Programme button 3 . Each time you press the button the value increases by one step; once a value of is reached the indicator jumps back to (Off: The rinse aid fill indicator 6 does not show a need to refill). Switch off the main switch 1 . The set value is stored within the device. Note Only switch off the rinse aid indicator if you are using cleaning products with integrated rinse aid! en Utensils Not suitable Cutlery and utensils made of wood. Fragile decorative glasses, hand-crafted and antique utensils. These decorative items are not dishwasher-proof. Plastic parts sensitive to hot water. Copper and tin utensils. Utensils which are soiled with ash, wax, lubricating grease or ink. Absorbent materials such as sponges and cloths. Aluminium and silver parts have a tendency to discolour and fade during the wash cycle. Even some types of glass (e.g. crystal glass objects) may turn cloudy after many wash cycles. Recommendation: In future buy utensils which are identified as dishwasher-proof. Damage to glassware and other dishes Possible causes: type of glass or manufacturing process chemical composition of detergent water temperature and duration of dishwasher programme. Suggested remedy: Use glassware or porcelain dishes that have been marked ’dishwasher–proof’ by the manufacturer. Use a mild detergent that is described as ’kind to dishes’. If necessary, seek further information from detergent manufacturers. Select a programme with as low a temperature and as short a duration as possible. To prevent damage, take glass and cutlery out of the dishwasher as soon as possible after the programme has ended. Loading the dishwasher Remove large food remnants. It is not necessary to rinse them off under running water. When loading the dishwasher, ensure that all utensils are secure and cannot fall over. the openings of all receptacles are face down. curved or indented utensils are at an incline, allowing water to drain. the two spray arms can rotate freely. Very small items should not be washed in the dishwasher as they could easily fall out of the baskets. Removing the dishes To prevent water dripping from the top basket onto the dishes in the lower basket, we recommend that...

Dieses Handbuch ist für folgende Modelle:
Geräte - SGVATN4/14 (2.79 mb)
Geräte - SGVATN4/16 (2.79 mb)
Geräte - SGVATN4/18 (2.79 mb)
Geräte - SHVATN4/01 (2.79 mb)