Stimmen - 0, Durchschnittliche Bewertung: 0
(
)
)
|
Anleitung Zusammenfassung
In this way water consumption can be reduced by approx. 4 litres. Switching the dishwasher ON Turn on the tap. Set main switch 1 to ON. Indicators light up according to the last programme that was selected. This same programme will run again if no other programme button 7 is pressed The numerical display 9 shows the expected duration of the programme. Close door. The programme starts automatically. Optical indicator during operation * * With some models During the rinse programme a light point appears on the floor below the device’s door. Only open the dishwasher door when the light point has disappeared. In the case of built-in dishwashers with flush front the light point will not be visible. Remaining running time display When the appliance has started, the expected programme running time is displayed. The programmed running time is affected by the water temperature, the number of dishes, as well as the degree of soiling. If these conditions are changed, the running time (depending on the selected programme) can vary greatly. As the effect is not detected until a programme is running, the time may be longer or shorter than expected. Time delay * * on applicable models You can delay the start of the programme in 1-hour steps up to 19 hours. Switch on the appliance. Press the timer programming button 3 until the digital display 9 jumps to . Keep pressing the timer programming button until the required time is displayed. en To delete the timer programming, keep pressing the button until is displayed. You can change your programme selection at any time until the programme starts. End of programme The end of the programme is indicated by a buzzer. This function can be changed as follows:– Hold down Function button C pressed and switch on main switch , then let the buttons go. Function Button C flashes, and the digital display indicates the value which was set at the factory (semi-loud). To change the setting: Press Function button C . Each depression of the button increases the set value by one, when is reached, the display jumps back to (off). Switch off the main switch 1 . The set value is stored in the appliance. Switching the dishwasher OFF Several minutes after the programme has ended: Open the door when the programme has ended. Set main switch 1 to OFF. Turn the water tap off. (Does not apply when Aqua-Stop unit has been fitted) Remove dishes, etc. when they have cooled down. At the end of the programme please open the door fully and not partially when emptying the dishwasher. Any escaping water vapour could damage sensitive worktops. Interrupting the programme Open the door. Caution! There is a risk of water squirting out from inside the appliance. Do not open the door fully until the spray arm has stopped rotating. Set main switch 1 to OFF. Indicator lights extinguish. The programme is retained in the dishwasher memory. If the hot water was switched ON or the appliance has already heated up and then the appliance door opened, leave the door ajar for several minutes and then close. Otherwise, the appliance door may fly open due to expansion. In order to continue with the stored programme, set the main switch to ON again and close the door. Terminating the programme (Reset) Simultaneously press programme buttons A and C for approx. 3 sec. The numerical display indicates . Close the door. The programme sequence lasts approx. 1 min. Switch off the main switch 1 . Intensive drying In the final rinse the appliance operates at a higher temperature and therefore an improved drying result is obtained. (Caution if utensils are fragile!) Hold down programme button A and press main switch until 1 the digital display illuminates. Release both buttons. The LED for button A flashes and the digital display 9 displays the factory setting (off) or (on). To change the setting, press programme button A . Switch off the main switch 1 . en Information on programme sequence When the appliance starts, the following displays are indicated. Sensors At the start of every programme all sensors (temperature sensor, Aqua sensor, motor sensor) are tested. Spray pressure Symbol indicates the different spray pressures in the system. Hygienic washing When the symbol is displayed, the utensils are hygienically clean. Keep the door closed, otherwise hygienic washing is not guaranteed. Programme sequence indicator Your dishes are being cleaned. Your dishes are being rinsed. Your dishes are being dried. Additional functions * on some models additional functions can be set with the buttons. 2 Eco option * Water and energy consumption can be reduced with the “Eco option” function. The running time is extended for optimum washing and drying results. Half load* If you have only a few items to wash (e.g. glasses, cups, plates), you can switch to “Half load”. The “half load” additional function saves water, energy and time. It is recommended to put a little less detergent in the detergent dispenser than for a full load. en Maintenance and care A...
Dieses Handbuch ist für folgende Modelle:Geräte - SGS69L12GB/13 (2.55 mb)
Geräte - SGS69L12GB/18 (2.55 mb)
Geräte - SGS69L12GB/20 (2.55 mb)
Geräte - SGS69L18GB/01 (2.55 mb)