Stimmen - 0, Durchschnittliche Bewertung: 0
(
)
)
|
Anleitung Zusammenfassung
No other settings on the appliance are required. Salt is still required if the water hardness is above 21 dH (37 fH, 26Clarke, 3.7 mmol/l). Fill the salt dispenser with salt 24 and select setting 6 on the water softening system. If in doubt, please contact the detergent manufacturer, especially if: the utensils are very wet at the end of the programme. limescale forms. en Note Optimum rinsing and drying results can be obtained by using standard detergents in conjunction with separate application of salt and rinse aid. Observance of the operating instructions or information on the packaging of the combined detergents determines their effectiveness. Note Even if the rinse aid and/or salt refill indicator is lit, the rinse programme runs correctly when 3in1 products are used. If the rinse aid refill indicator 7 or salt refill 6 indicator is defective and you would like to switch it off, proceed as follows: Switching the rinse-aid refill indicator off or on* * some models You can switch off the rinse-aid refill indicator 7 if you use a detergent with integrated rinse-aid. Close the door. Press and hold down button A . Press main switch 1 until the digital display lights up. Release both buttons. The digital display 8 indicates (rinse-aid refill indicator) and the button A flashes. By pressing button A you can switch the rinse-aid indicator off or on . Switch off the main switch 1 ; The setting is saved. “Remember to switch on the rinse-aid refill indicator again if you use a detergent without an integrated rinse-aid!” Switching the salt refill indicator / water softening system off and on Close the door Rotate the programme selector 3 from the 12 o’clock position by one notch to the left. Switch on main switch 1 and hold down for at least 3 sec. The digital display 8 indicates the current set hardness value and the salt refill indicator 6 flashes (hardness value has been set to 4 at the factory). To change the setting: Rotate the programme selector 3 . You can select a set value between 0 and 7 according to the hardness of your water. Switch off the main switch 1 . The chosen setting has now been stored. Note If you use the detergent and rinse aid separately or switch from combined detergents to standard cleaning products, ensure that the rinse aid refill indicator has been switched on and the water softening system has been set to the correct water hardness. en Overview of programmes The max. possible number of programmes is illustrated in this overview. The corresponding programmes for your appliance can be found on the fascia. Delicate Mixed Type of food remnants e.g. Amount of food remnants State of food remnant Type of Dishes e.g. porcelain, pans, cutlery, glasses, etc. MixedNon-sensitive Wash programme Soups, souffles, potatoes, pastries, rice, eggs, fried food Soups, potatoes, pastries, rice, eggs, fried food Coffee, cake, milk, sausage, cold drinks, salads Rinse off if the dishes have been stacked for several days in the dishwash er prior to washing. Large Little Very little Very adhesive Medium Lightly Adhesive Intensive 70. Auto 55-65. Eco 50. Gentle 40. Quick 45. Prerinse Programme- sequence Clean 70 Prerinse 40 Inter- mediate rinse Clean 40 Prerinse Clean 45 Dry Clean 55 Clean 55 Dry Clean 65 Clean 50 Prerinse Dry Clean 70 Dry The programme sequence isoptimised and adjusted accordingto the degree of soiling on theutensils. Prerinse Inter- mediate rinse Inter- mediate rinse Inter- mediate rinse Programme selection The most appropriate programme can be identified by comparing the type of crockery, cutlery, etc., as well as the amount and condition of food remains, with the details contained in the programme overview. You will find the appropriate programme information in the introduction. Washing dishes Reduce costs! If only a small number of dishes have been loaded into the dishwasher, selecting a programme that operates at the next lowest temperature will usually suffice. Programme specifications The programme specifications can be found in the summary of instructions. Programme specifications refer to normal conditions. Greater deviations may occur due to: varying amounts of dishes water supply temperature water pipe pressure ambient temperature mains voltage tolerances and the tolerances specific to the appliance (e.g. temperature, amount of water, etc.) The water consumption values refer to a set water hardness value of 4. Aqua sensor * * some models The Aquasensor is an optical measuring device (light barrier) which measures the turbidity of the rinsing water. en The Aqua sensor is used according to the programme. When the Aqua sensor is active, “clean” rinsing water may be transferred into the next rinsing bath and/or the temperature adjusted. If the turbidity is greater, the water is drained and is replaced with fresh water. In this way water consumption can be reduced by approx. 4 litres. Switching on the appliance Close the door. Turn on the tap fully. Rotate programme selector 3 to the requ...
Dieses Handbuch ist für folgende Modelle:Geräte - SF25M851TI/15 (2.13 mb)
Geräte - SF25M851TI/17 (2.13 mb)
Geräte - SF25M851TI/18 (2.13 mb)
Geräte - SF55M551TI/01 (2.13 mb)