|
Anleitung Zusammenfassung
Release both buttons. The digital display 7 indicates (rinse-aid refill indicator) and the button A flashes. By pressing button A you can switch the rinse-aid indicator off or on . Switch off the main switch 1 ; The setting is saved. “Remember to switch on the rinse-aid refill indicator again if you use a detergent without an integrated rinse-aid!” Note If you use the detergent and rinse aid separately or switch from combined detergents to standard cleaning products, ensure that the rinse aid refill indicator has been switched on. aus Programme overview This overview lists the max. possible number of programmes. The programmes supplied with your appliance are indicated on the fascia. 138 1,65 140 0,85 30 0,80 16 13,6 10 20 0,05 4 delicateNon- delicate Mixed Mixed Normal 45 Quick 45 Intensive 65 Pots and Pans 70 Pre-rinse Programme- sequence Wash programme Drying Rinse aid 70 First rinse Wash 70 Pre-rinse 50 Second rinse Programme details Laboratory measured value in accordance with AS/NZS 2007 Duration in minutes Electricity consumption in kWh Water consumption in litres very little a littlea lot stuck on hard loosely attached Drying Rinse aid 70 First rinse Wash 65 Pre-rinse Second rinse Drying Rinse aid 50 Wash 45 Pre-rinse Rinse aid 55 Main rinse Wash 45 Pre-rinse Type of crockery e.g. china, pots/pans, cutlery, glasses, etc. Type of food remains Amount of food remains Condition of food remains Soups, casseroles, sauces, potatoes, pasta, rice, eggs, roast or fried food Soups, potatoes, pasta, rice, eggs, roast or fried food Coffee, cakes, milk, sausage, cold drinks, salads Rinse off if the dishes have been stacked for several days in the dishwasher prior to washing. Third rinse Pre-rinse First rinse Second rinse 140 1,60 17 aus Washing dishes Reduce costs! If only a small number of dishes have been loaded into the dishwasher, selecting a programme that operates at the next lowest temperature will usually suffice. Programme data The stated programme data are based on standard operating conditions. The values can vary considerably according to: different amounts of dishes temperature of mains water supply pressure of mains water supply ambient temperature fluctuations in mains voltage machine-related factors (e.g. temperature, water volume, ...). Aqua sensor * * on applicable models The Aqua sensor is an optical measuring device which measures the turbidity of the rinsing water. A light barrier can detect dissolved food remnants in the water, e.g. egg, fat and oats. The Aqua sensor is used according to the programme. When the Aqua sensor is active, ”clean” rinsing water may be transferred into the next rinsing bath and/or the temperature adjusted. If the turbidity is greater, the water is drained and is replaced with fresh water. In this way the water consumption is reduced by approx. 4 litres for utensils which are ”less” dirty. Switching on the appliance Close the door. Turn on the tap fully. Rotate programme selector 3 to the required programme. Switch on the main switch 1 . The expected programme duration is indicated on the numerical display 7 . The programme sequence starts automatically. Remaining running time display When the appliance has started, the expected programme running time is displayed. The programmed running time is affected by the water temperature, the number of dishes, as well as the degree of soiling. If these conditions are changed, the running time (depending on the selected programme) can vary greatly. As the effect is not detected until a programme is running, the time may be longer or shorter than expected. End of programme The programme has ended when a figure appears in the numerical display 7 . Switching the dishwasher OFF Several minutes after the programme has ended: Set the main switch 1 to OFF. Turn the water tap off. (Does not apply when Aqua-Stop unit has been fitted) Remove dishes, etc. when they have cooled down. At the end of the programme please open the door fully and not partially when emptying the dishwasher. Any escaping water vapour could damage sensitive worktops. aus Interrupting the programme Switch off the main switch 1 . The lit display goes out. The programme is saved. If there is a warm water connection or if the machine has already heated up and the appliance door was opened, leave the door open for several minutes and then close. Otherwise, expansion may cause the appliance door to spring open. Switch on the main switch again. Terminating the programme (Reset) Only when the main switch is on: Rotate programme selector to the Reset position. The digital display indicates after approx. 3 sec. The programme sequence lasts approx. 1 min. When the programme has run, switch off the main switch 1 . To restart, rotate the programme selector 3 to the required programme. Switch on the main switch 1 . The programme sequence starts automatically. Changing the programme When the appliance is switched on, the programme can be changed within minutes. If the programm...
Dieses Handbuch ist für folgende Modelle:Geräte - SE3KLE2AU/82 (2.21 mb)
Geräte - SE3KLE2AU/86 (2.21 mb)