Stimmen - 0, Durchschnittliche Bewertung: 0
(
)
)
|
Anleitung Zusammenfassung
To change the setting: – Rotate programme selector 8. You can select a set value between ‹ and . according to the hardness of your water. – Switch off the main switch ( The chosen setting has now been stored. en Special salt $ Using special salt Always refill with special salt immediately before switching on the appliance. This ensures that overrun special salt solution is immediately washed out and does not corrode the rinsing tank. – Open the screw-type cap of the compartment 1Z. – Fill the tank with water (only required when switching on the appliance for the first time). – Then add salt (not table salt). The water is displaced and runs out. * depending on model The salt refill indicator P on the fascia is lit. It goes out as soon as a sufficiently high salt solution has formed. If the set value ‹ is displayed, do not add any salt because salt will not be used during operation of the appliance, the salt display is switched off. If the set values ‚ to . are displayed, salt must be added. Using detergents with salt component If combined detergents with a salt component are used, salt can usually be omitted up to a water hardness of 21° dH (37° fH, 26° Clarke, 3.7 mmol/l). If the water hardness is over 21° dH, special salt must be used. Salt refill indicator As soon as the salt refill indicator P on the fascia is lit, top up the salt. Depending on the washing frequency and the hardness setting, the regeneration salt may not have to be topped up for several months. If the salt refill indicator P is impaired (e. g. when using combined detergents containing salt component), it can be switched off. – Proceed as described under “Setting water softening system” and set the value to ‹. The water softening system and salt refill indicator are now switched off. a=Warnings – Never fill the salt dispenser with detergent. You will destroy the water softening system. – To prevent corrosion, always refill with salt immediately before switching on the appliance. en Rinse aid % As soon as the rinse-aid refill indicator X is lit on the fascia, there is still a rinse-aid reserve of 1–2 rinsing processes. Refill with rinse aid. The rinse aid is required for stain-free utensils and clear glasses. Use only rinse aid for domestic dishwashers. Combined detergents with rinse-aid component may be used up to a water hardness of 21° dH (37° fH, 26° Clarke, 3.7 mmol/l) only. If the water hardness is over 21° dH, rinse aid must be used. – Open the cover on the rinse-aid dispenser 9". To do this, press the mark (1) on the cover and simultaneously lift the cover on the control plate (2). – Carefully pour in the rinse aid to just below the edge of the filler opening. –Close cover until it clicks shut. –To prevent excessive foam formation during the next rinse cycle, remove any rinse aid which has run over with a cloth. Setting amount of rinse aid The rinse aid dispensing rate can be adjusted steplessly. The clear rinse controller was set to 4 at the factory. Do not change the position of the rinse aid control unless there are streaks (rotate towards –) or water stains (rotate towards +) on the utensils. . . Switching the rinse aid refill indicator off or on * * depending on model If the rinse-aid refill indicator X is impaired (e. g. when using combined detergents containing rinse aid component), it can be switched off. To change the setting: – Close the door. – Keep pressing the button # and press main switch ( until the digital display ` illuminates. – Release buttons. On the digital display ` ‚ is indicated (rinse-aid refill indicator on). – By pressing button # you can switch the rinse-aid indicator off ‹ or on ‚. – Switch off the main switch (; the chosen setting has now been stored. en 10 Not suitable – Cutlery and utensils made of wood. – Delicate decorative glasses, craft and antique utensils. These decors are not dishwasher-proof. – Plastic parts not resistant to heat. – Copper and tin utensils. – Utensils which are soiled with ash, wax, lubricating grease or ink. Aluminium and silver parts have a tendency to discolour and fade during the wash cycle. Even some types of glass (e.g. crystal glass objects) may turn cloudy after many wash cycles. Glass and utensil damage Causes: – Glass type and glass production process. – Chemical composition of the detergent. – Water temperature of the wash programme. Recommendation: – Use only glasses and porcelain which the manufacturer designates as dishwasher-proof. – Use a detergent which protects utensils. – Take glass and cutlery out of the dishwasher as soon as possible after the programme ends. Loading the dishwasher – Remove large food remnants. It is not necessary to prerinse utensils under running water. – Place the utensils so that – they are secure and cannot tip over. – all utensils with their openings face down. – parts with curves or indentations are at an angle, thereby allowing water to drain. – does not obstruct rotation of the two spray arms 12 and 1B. Very small utensils s...