Stimmen - 0, Durchschnittliche Bewertung: 0
(
)
)
|
Anleitung Zusammenfassung
The dishwasher must be disconnected from the electricity supply before any repairs or other work are started. Pull the mains plug out of the wall socket or switch off at the fuse box. Grasp the plug to remove it from the socket; do not tug on the cable. Turn the water off at the tap. When disposing of old appliances Appliances that have reached the end of their service life should be rendered inoperable in order to exclude the possibility of subsequent accidents. Pull the mains plug out of the wall socket, cut through the connecting cable and disable the door lock. Take the appliance to a designated waste disposal centre. Warning Children could get locked in the appliance (risk of suffocation) or get stuck in other positions. Therefore: Remove the mains plug, cut the mains wire and set aside. Damage the door lock so that the door can no longer be closed. Before using for the first time The appliance was checked before it left the works. In order to remove possible water test remains, use the appliance for the first time without any dishes, using the highest temperature. Also fill salt, rinse aid and detergent in the filling compartments. en Getting to know your appliance Diagrams of the control panel and the interior of the appliance can be found in the envelope at the front. Individual positions are referred to in the text. Control panel 1 Main switch 2 Door Opener 3 Programme selector (retractable*) 4 Additional options* 5 “Check water supply” display 6 Programme sequence display 7 “End of programme” display 8 Rinse-aid refill indicator 9 Salt refill indicator * some models Appliance interior 20 Top basket 21 Additional cutlery basket for the top basket * 22 Top spray arm 23 Additional cup rack * 24 Bottom spray arm 25 Float ** 26 Bottom basket 27 Salt dispenser 28 Filters 29 Cutlery basket 30 Dispenser for rinse aid 31 Detergent dispenser 32 Catch 33 Rating plate * some models ** The float ensures that the appliance interior is not overfilled. Only customer service may maintain, remove and install the float. You will need to purchase the following before using the dishwasher for the first time: – special salt for use in dishwashers – detergent – rinse-aid Only use products, which are suitable for dishwashers. en Water softener In order to rinse dishes and glasses satisfactorily, the dishwasher requires soft water, i.e. containing little or no lime, otherwise water stains will be left behind on crockery and glasses, etc. If the tap water exceeds a certain level of hardness, it must be softened, i.e. decalcified, so that it can be used in the dishwasher. This is achieved by adding a special salt to the water softener inside the dishwasher. The water softener, that is the required amount of salt, is set up according to how hard the tap water is. Setting up the water softener Determine the level of hardness of your tap water. Your local water company or service agent can help you with this. Identify setting from the following water hardness table. Close the door Water hardness table Rotate the programme selector 3 from the 12 o’clock position by one notch to the left. Switch on main switch 1 and hold down for at least 3 sec. The display 9 flashes and the lamps above the symbols and light up. (hardness value has been set to 2 at the factory). To change the setting: Rotate the programme selector 3 . You can select a set value between 0 and 3 according to the hardness of your water. If the lamps , and light up, the maximum set hardness value has been reached. If the set hardness value is now increased again, the lamps go out and the set hardness value is set to 0 (no lamp lights up). Switch off the main switch 1 . The chosen setting has now been stored. dh fH Clarke mmol/l 0–6 0–11 0–8 0–1,1 0 7–16 12–29 9–20 1,2–2,9 1 17–21 30–37 21–26 3,0–3,7 2 22–35 38–62 27–44 3,8–6,2 3 en Filling in the Salt Function of the salt During the rinse cycle the salt is being washed automatically from the salt compartment into the softening system where it will dissolve the lime. The lime-containing solution drains from the dishwasher. Afterwards the softening system is ready to be loaded again. This regeneration cycle will only work if the salt is dissolved in water. Open the screw-type cap of the compartment 27 . Before switching on the appliance for the first time, pour approx. 1 litre of water into the salt dispenser. Then refill with salt (not cooking salt) until the salt container is full (max. 1.5 kg). When you refill the salt, water is being displaced and drains off. Therefore, to prevent corrosion, always refill with salt immediately before switching on the dishwasher. This way the overflowing salt solution is diluted and flushed immediately. Use the enclosed salt filling aid ( in some models). Then clean the filling area of salt residues and screw the compartment lid back on without tilting the lid. * on applicable models The LOW SALT indicator 9 on the front panel will light up initially but will extinguish again after...
Dieses Handbuch ist für folgende Modelle:Geräte - SE23E231EU/22 (725.28 kb)