Stimmen - 0, Durchschnittliche Bewertung: 0
(
)
)
|
Anleitung Zusammenfassung
containing low amounts of lime, otherwise white limescale will be deposited on the utensils and inner container. Tap water above a specific degree of water hardness must be softened, i.e. descaled, for use in a dishwasher. Water is softened with special salt in the water softening system of the dishwasher. The setting and therefore the required amount of salt depends on the degree of hardness of your tap water (see table). Setting The amount of salt dispensed can be set in 4 stages depending on the hardness of your water. Accordingly 0, 1, 2 or 3 displays are lit (see table). Factory setting: 1. Water hardness table – Find out about the hardness value of your tap water. Your water utility company will help you with this. – Setting can be found in the water hardness table. – Open the door. – Switch on ON/OFF switch (. – Hold down button > P and press START button h until the End display ` and salt refill indicator )* flash. – Release buttons. The salt refill indicator )* flashes and the display # is lit (= Setting 1). To change the setting, – Press the button < H until the required setting has been selected. – Press START button h. The displays ` and )* go out. The selected setting is saved. – Close the door. . . . !. . . . . . . . . en Special salt $ Using special salt Always refill with special salt immediately before switching on the appliance. This ensures that overrun special salt solution is immediately washed out and does not corrode the rinsing tank. – Open the screw-type cap of the compartment 1J. – Fill the tank with water (only required when switching on the appliance for the first time). – Then add dishwasher salt (not table salt or tablets). The water is displaced and runs out. As soon as the salt refill indicator )* on the fascia is lit, top up the salt. * depending on model Using detergents with salt component If combined detergents with a salt component are used, salt can usually be omitted up to a water hardness of 21° dH (37° fH, 26° Clarke, 3.7 mmol/l). If the water hardness is over 21° dH, special salt must be used. Switching off salt refill indicator/ water softening system If the salt refill indicator )* is impaired (e.g. when using combined detergents containing salt component), it can be switched off. – Proceed as described under “Adjusting the water softening system” and select setting 0. The water softening system and salt refill indicator are now switched off. a=Warning Never fill the salt dispenser with detergent. You will destroy the water softening system. en Rinse aid % As soon as the rinse-aid refill indicator )" is lit on the fascia, there is still a rinse-aid reserve of 1 – 2 rinsing processes. Refill with rinse aid. The rinse aid is required for stain-free utensils and clear glasses. Use only rinse aid for domestic dishwashers. Combined detergents with rinse-aid component may be used up to a water hardness of 21° dH (37° fH, 26° Clarke, 3.7 mmol/l) only. If the water hardness is over 21° dH, rinse aid must be used. – Open the dispenser 1j by pressing and lifting the plate on the cover. – Carefully pour rinse aid up to the max. mark in the filler opening. –Close cover until it clicks shut. –To prevent excessive foam formation during the next rinse cycle, remove any rinse aid which has run over with a cloth. Setting amount of rinse aid The amount of rinse aid dispensed can be set in 4 stages. Accordingly 0, 1, 2 or 3 displays are lit (see water hardness table). Factory setting: 1. Do not change the amount of rinse aid unless streaks (select lower setting) or water stains (select higher setting) are left on the utensils. – Open the door. – Switch on ON/OFF switch (. – Hold down button > P and press START button h until the End display ` and salt refill indicator )* flash. – Release buttons. – Keep pressing button > P until the rinse aid refill indicator )" flashes. The rinse aid refill indicator )" flashes and the display # is lit (= Setting 1). To change the setting: – Press the button < H until the required setting has been selected. – Press START button h. The displays ` and )" go out. The selected setting is saved. – Close the door. Switching off rinse-aid refill indicator If the rinse-aid refill indicator )" is impaired (e.g. when using combined detergents containing rinse-aid component), it can be switched off. – Proceed as described under “Setting amount of rinse aid” and select setting 0. The rinse aid refill indicator )" is now switched off. en 9 Not suitable – Cutlery and utensils made of wood. – Delicate decorative glasses, craft and antique utensils. These decors are not dishwasher-proof. – Plastic parts not resistant to heat. – Copper and tin utensils. – Utensils which are soiled with ash, wax, lubricating grease or ink. Aluminium and silver parts have a tendency to discolour and fade during the wash cycle. Even some types of glass (e.g. crystal glass objects) may turn cloudy after many wash cycles. Glass and utensil damage Causes: – Glass type and ...
Dieses Handbuch ist für folgende Modelle:Geräte - DRV4303/06 (1.28 mb)
Geräte - DRV4303/07 (1.28 mb)
Geräte - DRV4303/09 (1.28 mb)