Stimmen - 0, Durchschnittliche Bewertung: 0
(
)
)
|
Anleitung Zusammenfassung
4 litres. Switching the dishwasher ON Set main switch 1 to ON. Indicators light up according to the last programme that was selected. This same programme will run again if no other programme button 9 is pressed. The programme starts automatically. Remaining running time display When the appliance has started, the expected programme running time is displayed. The programmed running time is affected by the water temperature, the number of dishes, as well as the degree of soiling. If these conditions are changed, the running time (depending on the selected programme) can vary greatly. As the effect is not detected until a programme is running, the time may be longer or shorter than expected. * on applicable models You can delay the start of the programme in 1-hour steps up to 19 hours. Switch on the appliance. Press the timer programming button 4 until the digital display 3 jumps to . Keep pressing the timer programming button until the required time is displayed. To delete the timer programming, keep pressing the button until is displayed. You can change your programme selection at any time until the programme starts. End of programme The programme has ended when a figure appears in the numerical display 3 . Switching the dishwasher OFF Several minutes after the programme has ended: Set the main switch 1 to OFF. Turn the water tap off. (Does not apply when Aqua-Stop unit has been fitted) Remove dishes, etc. when they have cooled down. At the end of the programme please open the door fully and not partially when emptying the dishwasher. Any escaping water vapour could damage sensitive worktops. Interrupting the programme Switch off the main switch 1 . The lit display goes out. The programme is saved. If there is a warm water connection or if the machine has already heated up and the appliance door was opened, leave the door open for several minutes and then close. Otherwise, expansion may cause the appliance door to spring open. Switch on the main switch again. Terminating the programme (Reset) Simultaneously press programme buttons A and C for approx. 3 sec. The numerical display indicates . The programme sequence lasts approx. 1 min. Switch off the main switch 1 . Changing the programme When the appliance is switched on, the programme can be changed within minutes. If the programme is changed subsequently, programme sections (e.g. Cleaning) which have already started run to the end. The new remaining time consists of the remaining time of the previous programme section and the remaining time of the newly selected programme. Intensive drying In the final rinse the appliance operates at a higher temperature and therefore an improved drying result is obtained. (Caution if utensils are fragile!) Close the door. Hold down programme button A and press main switch until 1 the digital display illuminates. Release both buttons. The LED for button A flashes and the digital display displays the factory setting (off) or (on). To change the setting, press programme button A . Switch off the main switch 1 . Additional options * depending on model Additional options 5 can be set with the buttons. Turbo * The programme running time is reduced significantly in the Turbo programme. The energy consumption is increased by up to 30% due to more intensive heating. The time reduction affects the following programmes: Auto: Time reduction up to 25 % Eco: Time reduction up to 58 % Half load * If you have only a few items to wash (e.g. glasses, cups, plates), you can switch to “half load”. This will save water, energy and time. It is recommended to put a little less detergent in the detergent dispenser than for a full load. Hygiene * The temperature is increased during the rinsing process. This increases the hygiene status. This additional option is ideal for cleaning e.g. chopping boards and baby bottles. IntensiveZone * Perfect for a mixed load. You can wash very soiled pots and pans in the lower basket together with normally soiled utensils in the upper basket. The spray pressure in the lower basket is intensified, the rinsing temperature is increased slightly. Extra drying * An increased temperature during the final rinse and an extended drying phase mean that even plastic parts dry well. There is a slight increase in the energy consumption. 14 Maintenance and care A regular inspection and maintenance of your machine will help to prevent faults. This saves time and prevents problems. Overall condition of the machine Check washing chamber for grease and limescale deposits. If you find such deposits: Fill the detergent dispenser with detergent, start the appliance without utensils in the programme which has the highest wash temperature. Clean the appliance with detergents/ appliance cleaners which are particularly suitable for use with dishwashers. Regularly wipe the door seal with a damp cloth. Never use a steam cleaner to clean your dishwasher. The manufacturer is not liable for any consequential damage. Regularly wipe the front ...
Dieses Handbuch ist für folgende Modelle:Geräte - DI240410/15 (1.98 mb)
Geräte - DI240410/17 (1.98 mb)
Geräte - DI240410/18 (1.98 mb)