Stimmen - 0, Durchschnittliche Bewertung: 0
(
)
)
|
Anleitung Zusammenfassung
decalcified, so that it can be used in the dishwasher. This is achieved by adding a special salt to the water softener inside the dishwasher. The water softener, that is the required amount of salt, is set up according to how hard the tap water is. Setting up the water softener Determine the level of hardness of your tap water. Your local water company or service agent can help you with this. Identify setting from the following water hardness table. Water hardness table Press and hold the B programme button, and set the main switch 1 to ON, before releasing the programme button again. The indicator lamp for the B button flashes, as does the figure in the numerical display. The latter represents the value that was pre-set in the factory. To change the setting: Press the B programme button 6 . Every time the button is pressed, the figure increases by one. After reaching , the display starts at again. Set the main switch 1 to OFF. The new setting is stored in the appliance’s memory. Approx. 4 litres of water are required for regenerating the water softening system. The overall water consumption per load can therefore be increased by between 0 and a maximum of 4 litres according to the water hardness setting. en Filling the special salt container How the salt works While washing is taking place, salt is automatically rinsed out of the salt container into the water softener where it dissolves the lime in the water. The dissolved lime is pumped out of the dishwasher. The water softening system is then ready for the next load. This process of regeneration can only function when the salt is dissolved in water. Unscrew the lid on the salt container 24 . Before you use the dishwasher for the first time, pour approx. 1 litre of water into the salt container. Use the enclosed salt filler. Refill with salt (do not use edible salt) until the salt dispenser is full (max. 1.5 kg). When the salt dispenser is being refilled, water is displaced and drains away. Therefore always refill the salt dispenser immediately before switching on the dishwasher (to prevent corrosion). As a result, the overflowing salt solution will be immediately diluted and rinsed out. Then remove salt residue from the filler area and screw on the dispenser cover, ensuring that it is not fitted askew. The LOW SALT indicator 7 on the front panel will light up initially but will extinguish again after a short period when the salt solution has become sufficiently concentrated. Note When the control is set to , it is not necessary to fill up with salt as none will be consumed while the dishwasher is operating. The LOW SALT indicator is switched off. If the control is set between and , then salt must be added to the dispenser. Do not pour detergent into the container for special salt. This would destroy the water softener. Salt refill indicator As soon as the salt refill indicator 7 is lit on the control panel, refill with salt immediately before the next rinse cycle. en Filling the rinse-aid container The purpose of a rinse-aid is to prevent the formation of water marks on tableware and utensils, and to ensure that glasses are clean and sparkling. The rinse-aid is consumed during the washing process. Fold back the lid on the rinse-aid container 29 . To open the lid, press the mark (1 ) on the rinse-aid lid and simultaneously lift the lid off the lug (2 ). 1 2 Pour the rinse-aid into the filler hole until the level indicator turns dark. Adjusting the amount of rinse-aid The amount of rinse-aid added to the water can be varied by adjusting the stepless control. The rinse-aid control has been set to ”4” in the factory. Do not alter the setting of the rinse-aid control unless streaks (turn knob towards ”–”) or water marks (turn knob towards ”+”) are left on the dishes. 29 rinse–aid control Low rinse-aid indicator Close the lid, ensuring that you hear it snap closed. Use only rinse aid for domestic dishwashers. Spilt rinse aid may result in excessive foam formation in the next rinse cycle. Therefore, remove any spilt rinse aid with a cloth. As long as the rinse-aid refill indicator on the panel 829 (on applicable models) or dispenser has not illuminated, there is sufficient rinse-aid in the dishwasher. LOW RINSE-AID indicator en Switching the rinse-aid indicator on or off You can switch the rinse-aid indicator 8 on or off. This function can be changed as follows: Close the door. Hold down programme button C and press main switch 1 until the digital display illuminates, then release the buttons. On the digital display 3 is indicated (rinse-aid indicator on). By pressing the programme button C you can switch the rinse-aid indicator off or on . Switch off the main switch 1 ; the chosen setting has now been stored. Note Do not switch off the rinse-aid indicator unless you are using detergent products with an integrated rinse-aid! Unsuitable dishes You should not clean the following items in your dishwasher: Cutlery and dishes made of wood. They will leach out and be...
Dieses Handbuch ist für folgende Modelle:Geräte - CG564J5/52 (2.11 mb)
Geräte - CG564J5/56 (2.11 mb)
Geräte - CG564J5/70 (2.11 mb)
Geräte - CG564J7/35 (2.11 mb)