Stimmen - 1, Durchschnittliche Bewertung: 3 ( )

Hersteller: Amana Dateigröße: 7.2 mb Dateiname: Unterrichtssprache:

ABCDEH GF A. Drain hose—cut here, if needed E. Drain hose B. Screw-type clamps F. Rubber hose connector (not provided) C. Air gap G. Disposer inlet (provided) H. Drain trap D. Large drain hose clamp 4. Insert the drain hose through the hole cut in the cabinet and to the front and center of the opening where the drain connection will be made. A A. Drain hose Connect Drain Hose to Air Gap—No Waste Disposer 1. Cut the end of the drain hose, if needed. NOTE: Do not cut the ribbed section. 2. Attach the drain hose to the air gap with the large drain hose clamp (provided). NOTE: If the drain hose was cut, use 1..." to 2" (3.8 to 5 cm) screw-type clamp (not provided). 8 3. Use a rubber hose connector (not provided) with screw-type clamps (not provided) to connect the air gap to the waste tee above the drain trap and at least 20" (50.8 cm) above the floor. 4. Insert the drain hose through the hole cut in the cabinet and to the front and center of the opening where the drain connection will be made. Connect Drain Hose to Waste Disposer—No Air Gap 1. Remove the waste disposer knockout plug. NOTE: Do not cut the end of the drain hose. 2. Attach the drain hose to the waste disposer inlet with the large drain hose clamp (provided). This connection must be before the drain trap and at least 20" (50.8 cm) above the floor. NOTE: It is recommended that the drain hose be looped up and securely fastened to the underside of the counter. 3. Insert the drain hose through the hole cut in the cabinet and to the front and center of the opening where the drain connection will be made. Connect Drain Hose—No Waste Disposer or Air Gap 1. Cut the end of the drain hose, if needed. NOTE: Do not cut the ribbed section. 2. Attach the drain hose to the waste tee with the large drain hose clamp (provided). NOTES: ¦ If the drain hose was cut, use 1..." to 2" (3.8 to 5 cm) screw-type clamp (not provided). ¦ This connection must be before the drain trap and at least 20" (50.8 cm) above the floor. ¦ It is recommended that the drain hose be looped up and securely fastened to the underside of the counter. A. Drain hose—cut here, if needed B. Screw-type clamps (not provided) C. Air gap D. Large drain hose clamp (provided) E. Drain hose F. Rubber hose connector (not provided) G.Waste tee H. Drain trap A. Drain hose E D C G H A B F A A. Large drain hose clamp (provided) B. Drain hose C. Disposer inlet D. Drain trap A. Drain hose A. Drain hose—cut here, if needed B. Large drain hose clamp (provided) C. Drain hose D. Drain trap E. Waste tee B A C D A E D C A B 9 Prepare Dishwasher 1. Fold insulation down over back and sides of dishwasher (on some models). 2. Using 2 or more people, place the dishwasher on its back on a piece of cardboard. NOTE: If the door panel will be used as a work table, place a towel over it to avoid damage to the door panel. 3. Using a ..." hex socket, nut driver or Phillips screwdriver, remove the 4 screws attaching the toekick panel and lower panel to the dishwasher. NOTE: Do not remove the tech sheet from the access panel. 4. Remove both panels and set aside on a covered surface. 5. Apply plumber’s tape or pipe joint compound to the 90. elbow fitting and connect the fitting to the water inlet valve. 6. Tighten the 90. elbow fitting until snug. NOTE: Elbow should face to the rear of the dishwasher. WARNING Tip Over Hazard Do not use dishwasher until completely installed. Do not push down on open door. Doing so can result in serious injury or cuts. WARNING Excessive Weight Hazard Use two or more people to move and install dishwasher. Failure to do so can result in back or other injury. A.Water inlet valve B. Elbow A B 10 Prepare Terminal Box 1. Using a ..." hex-head socket, nut driver or Phillips screwdriver, remove the terminal box cover. Lay the cover aside. 2. Install a UL-listed/CSA-approved conduit connector (may be provided in power supply cord kit [Part Number 4317824]). Check that screwheads are facing to the left when tightening the conduit nut. NOTE: If your dishwasher will be connected by the direct wire connection, please see “Adjust Leveler Legs.” Make Electrical Connections—Power Supply Cord Method The power supply cord and connections must comply with the National Electrical Code, Section 422 and/or local codes and ordinances. Install the power supply cord according to the installation instructions included with the power supply cord kit. 1. Route the power supply cord so that it does not touch the dishwasher motor or the lower part of the dishwasher tub. 2. Pull the power supply cord through the conduit connector in the terminal box. 3. Remove the green grounding screw and place the screw through the ring terminal of the green ground wire. Reattach and tighten the green grounding screw. 4. Using UL-listed/CSA approved twist-on connectors sized to connect the power supply cord to 16-gauge dishwasher wire, connect the white wire from the power supply cord to the white wire on the terminal box. WARNING Electrical Sho...

Herunterladen

Geben Sie zwei Ziffern: