Stimmen - 4, Durchschnittliche Bewertung: 4 ( )

Hersteller: Kenmore Dateigröße: 2.67 mb Dateiname: Unterrichtssprache:

Incorrect loading may cause poor washing and the need to rewash all or part of the loado Use the delay feature to run your dishwasher during off-peak hours. Local utilities recommend this to avoid heavy usage of energy at certain times of day. Customized wood panels Your dishwasher can be customized with wood panels, A heavy-duty door spring kit (Part No, 4318050) is needed if the upper panel weighs more than 4 pounds. The maximum weight for the upper panel and door is 8 pounds , ,,, i,,,,,,, = Upper panel t. Insert a finger under one end of the retainer, Pull the retainer towards you in a peeling action. Set retainer aside 2, Lift color panels at outer edges. Use one hand to • bow bottom of panel Do not remove spacer, Remove color panel(s)_ 3, With desired color facing out, insert one side of color panel into door frame,. 4, Bow color panel and insert other side into ! door frame.. 5, Push in on color panel(s) near the top and slide panel(s) and spacer up inside bottom of control panel panel. Let color panel(s) rest on channel at bottom of doors. Channel 6, Snap one end of retainer into channel as shown. Push inward while sliding thumb along full length of retainer., Channel Color panel Retainer in along full Spacer Snapinto channel length of retainer 2t Access panel . Push up with thumbs on each end of access 3. With desired color facing out, slide access panel panel top trim to unsnap into access panel frame. trim, Remove trim and set aside,, % 2. Carefully slide access oanel upward and remove. 4. Make sure access panel has slid into groove Do not remove spacer. along bottom of access panel frame. 5. Line up edges of top trim with sides of access panel frame. Tilt back of trim down and slide into placer Snap front of trim down to cover top edge of access panel, Thefollowingchartisaconvenientchecklistforhandlingminorperformanceproblems.Gooverthislistbefore callingforservice.Ifyouareunableto solveyourdishwasher'sproblem,pleasesee"Troubleshooting." Ifyou stillneedhelp,see"SearsRepairServices"toll-freenumbersonpage27. PROBLEM Food soil left on dishes Spotting and filming CAUSE Improper loading Water temperature is too low Use of incorrect, too little, or ineffective detergent Detergent cakes in dispenser Pump or spray arm clogged by labels from bottles and cans Low water pressure caused by insufficient fill Slowdown of wash arm due to high suds Hard water or high mineral content in water Water temperature is too low Use of incorrect detergents Incorrect amount of detergent Use of ineffective detergents SOLUTION Follow loading instructions on pages 13-17o Use the Water Heat option.. If needed, turn home water heater up to ensure water entering dishwasher is 120°F (49°C) minimum See "Water temperature tips" on page 12. Use recommended dishwasher detergents onlyo Follow recommendations on page 11 for amounts; never use less than 1 tablespoon per load. Detergent must be fresh to be effective. Always store detergent in a cool, dry area. Use fresh detergent only. Do not allow detergent to sit for several hours in a wet dispenser. Check dispenser for caked detergent° Clean dispenser when caked detergent is present. Remove labels before washing bottles and cans or wash by hand° See page 18. Home water pressure should be 20 to 120 pounds per square inch (psi) for proper dishwasher fill. A booster pump on the water supply may be necessary if pressure is too low. Never use soap or laundry detergents. Use recommended dishwasher detergents only. Conditioning the final rinse water with a liquid rinse agent helps eliminate spotting and filming. Keep the dispenser full with a rinse agent at ail times. Use the Water Heat option, if available.. If needed, turn home water heater up to ensure water entering dishwasher is 120°F (49°C) minimum. See "Water temperature tips" on page 12. Use recommended dishwasher detergents oniy Follow recommendations on page 11 for amount, Heavy soil and/or hard water generally require extra detergent. Detergent should be fresh. Store in a cool, dry place, preferably in an airtight container. Discard lumpy detergent.. continued on next page PROBLEM Spotting and filming (cont.) Cycle takes extremely long time Dishes do not dry completely Silica film or etching (silica film is a white iridescent deposit; etching is a cloudy film) Black or gray marks on dishes Brown stains on dishes and dishwasher interior CAUSE Insufficient fill caused by tow water pressure Water temperature is too low Dishes do not drain properly Plastics Rinse agent dispenser is empty A water chemical reaction with certain types of glassware. Usually caused by some combination of soft or softened water, alkaline washing solutions, insufficient rinsing, overqoading the dishwasher, and heat of drying. Aluminum items High iron content in water supply SOLUTION Home water pressure should be 20 to 120 psi for proper dishwasher fill. A booster pump on the water supply may be necessary if pressure is too low NOTE:To remove spots and film ...

Herunterladen

Geben Sie zwei Ziffern: