Stimmen - 1, Durchschnittliche Bewertung: 3 ( )

Hersteller: Haier Dateigröße: 252.71 kb Dateiname: Unterrichtssprache:

To cancel the time delay setting, pressing the Delayed Start button until the delayed start indicator “ E” goes out. Press programme button “ I ” to choose the desired programme. E DF I If the the door is closed, after 5 seconds the delayed start indicator “ E ” lights , the time-remaining indicator “ F ” will blink and decrease , the programme will start until the delayed start indicator “ F ” goes out . Cancelling or modifying a cycle A cycle that is underway can be modified if it has only been running for a short time. Otherwise, the detergent may have already been used, and the appliance may have already drained the wash water. If this is the case, the detergent dispenser must be refilled ( see the paragraph entitled, “ Loading the detergent ”). To modify a cycle that is already underway, press the button“ A ” , all of the settings will be cancelled. To set a new cycle, follow the instructions contained in the paragraph entitled “Switching the dishwasher ON”. Speedup Wash You could save your washing time when push button “C” after choosing the programme. (except for soak programme) Suggestion Use this function when there is less cutlery loading. C AB How to keep your dishwasher in shape After Every Wash After every wash, turn off the water supply the appliance and leave the door slightly ajar so that moisture and odors are not trapped inside. Remove the plug Before cleaning or performing maintenance, always remove the plug from the socket. Do not run risks. No solvents or Abrasive Cleaning Products To clean the exterior and rubber parts of the dishwasher, do not use solvents or abrasive cleaning products. Rather, use only a cloth and warm soapy water. To remove spots or stains from the surface of the interior, use a cloth dampened with water and a little while vinegar, or cleaning product made specifically for dishwashers. Moving the Appliance If the appliance must be moved, try to keep it in a vertical position. If absolutely necessary, it can be positioned on its back. Seals One of the factors that cause odors to form in the dishwasher is food that remains trapped in the seals. Periodic cleaning with a damp sponge will prevent this from occurring. The door should not be left in the open position since this could present a tripping hazard. When You Go on Holiday When you go on holiday, it is recommended that you run a wash cycle with the dishwasher empty and then remove the plug from the socket, turn off the water supply and leave the door of the appliance slightly ajar. This will help the seals last longer and prevent odors from forming within the appliance. Care and maintenance Regular inspection and maintenance of your appliance helps to prevent problems from occurring.This saves time and aggravation.You should therefore carefully inspect the inside of your dishwasher from time to time. Overall condition of appliance Check that no grease or scale has accumulated on the inside of the dishwasher. If you discover any deposits: Clean the interior of the dishwasher thorughly with a detergent solution. Dishwasher salt H Check the LOW SALT indicator “ G” .Top up with salt, if required. Rinse-aid G Check the LOW RINSE AID indicator “ H ”, on the front panel. Top up with rinse-aid,if required. Filters The filters “ 8”,“ 9” prevent larger particles of food in the water from reaching the pump.These particles may occasionally block the filters. When the appliance has finished washing, check the filters for particles of food and, if required, clean. After undoing the coarse micro-filter “ 8 ” , the filter unit “ 10” can be removed. Remove any particles of food and rinse the filters under running water. Insert the filter unit “ 9 ” and tighten the coarse micro- filter. 8 9 Spray arms Lime and remnants of food in the washing water can block the nozzles in the spray arms “ 10 ” and “ 11 ” and the arm mountings. Inspect the nozzles in the spray arms for blocked holes due to remnants of food. If necessary, pull the lower arm “ 11 ” upwards and lift it off. Unscrew the upper spray arm “ 10 ”. Clean both spray arms under running water. Refit the spray arms. Ensure that the lower arm has locked into place and the upper one is screwed tight. 10 11 Fault finding Resolving minor problems yourself Experience has shown that you can resolve most problems that rise during normal daily usage yourself, without having to call out a service engineer.Not only does this save costs,but it also means that the appliance is available for use again that much sooner. The following list of common occurrences and their remedies should help you identify the causes of most problems. Problems... ...when the appliance is switched on Appliance does not start up Fault with fuse in mains electricity supply. Plug not inserted in wall socket. Appliance door not closed properly. Programme button has not been pressed. Water tap not turned on. Blocked strainer in water intake hose. -The strainer is situated in the Aquastop or supply-hose connection. Ca...

Herunterladen

Geben Sie zwei Ziffern: