Stimmen - 3, Durchschnittliche Bewertung: 3.7 ( )

Hersteller: Haier Dateigröße: 262.7 kb Dateiname: Unterrichtssprache:

Overall condition of appliance Check that no grease or scale has accumulated on the inside of the dishwasher. If you see any deposits: Clean the interior of the dishwasher thorughly with a detergent solution. Filters The filters “ 8”,“ 9” prevent larger particles of food in the water from reaching the pump.These particles may occasionally block the filters. When the appliance has finished washing, check the filters for particles of food and, if required, clean. After undoing the coarse micro-filter “ 8 ” , the filter unit “ 9” can be removed. Remove any particles of food and rinse the filters under running water. Insert the filter unit “ 9 ” and tighten the coarse micro-filter. Spray arms Lime and remnants of food in the washing water can block the nozzles in the spray arms “ 10 ” and “ 11 ” and the arm mountings. Inspect the nozzles in the spray arms for blocked holes due to remnants of food. If necessary, pull the lower arm “ 11 ” upwards and lift it off. Unscrew the upper spray arm “ 10 ”. Clean both spray arms under running water. Refit the spray arms. Ensure that the lower arm has locked into place and the upper one is screwed tight. 8 9 11 10 Washing dishes Programme selection The most appropriate programme can be identified by comparing the type of crockery, cutlery, etc., as well as the amount and condition of food remains, with the details contained in the wash cycle table.The corresponding programme sequence, duration and consumption details are shown in the right half of the overview. For example: Use the« normal» programme for dishes and utensils which have plenty of food remains stuck on hard. Savings If only a small number of dishes have been loaded into the dishwasher,selecting a programme that operates at the next lowest temperature will usually be sufficient. Programme data The stated programme data are based on standard operating conditions. The values can vary considerably according to: different amounts of dishes temperature of mains water supply pressure of mains water supply ambient temperature fluctuations in mains voltage machine-related factors (e.g. temperature, water volume,...) Energy and water consumption is reduced by up to 1/4 when dishes are washed in the upper basket only.The water consumption values are related to water hardness level 1. Switching the dishwasher ON Turn on the tap. Set ON-OFF button “ A ” to ON. All the programme indicators“C1,C2,C3, C5,C6”light . Press programme button “B1-6”,programme indicator “ C1-6” blinks. If the door is closed, after 5 seconds, the programme indicator “ C1” lights steady and the dishwasher beeps once time, then the programme starts automatically. How to keep your dishwasher in shape After Every Wash After every wash, turn off the water supply (not necessary for models with “Aquastop” ) the appliance and leave the door slightly ajar so that moisture and odors are not trapped inside. Remove the plug Before cleaning or performing maintenance, always remove the plug from the socket. Do not run risks. No solvents or Abrasive Cleaning Products To clean the exterior and rubber parts of the dishwasher, do not use solvents or abrasive cleaning products. Rather, use only a cloth and warm soapy water. To remove spots or stains from the surface of the interior, use a cloth dampened with water and a little white vinegar, or cleaning product made specifically for dishwashers. EN End of programme Six beeps will indicate that the wash cycle has finished and all the programme indicators light. Switching the dishwasher OFF Several minutes after the programme has ended: Set main switch “A” to OFF. Open the door . Turn the water tap off. (Does not apply when Aquastop unit has been fitted) Remove dishes, etc. when they have cooled down. Interrupping the programme Open the door. Caution! There is a risk of water squirting out from inside the appliance. Do not open the door fully until spray arm has stopped rotating. When you open the door, the dishwasher will beep ten times every thirty seconds. If the appliance has already heated up or the hot water was switched ON and then the appliance door opened, leave the door ajar for several minutes and then close. Otherwise, the appliance door may open due to expansion. Cancelling or modifying a cycle A cycle that is underway can be modified if it has only been running for a short time. Otherwise, the detergent may have already been used, and the appliance may have already drained the wash water. If this is the case, the detergent dispenser must be refilled ( see the paragraph entitled, “ Loading the detergent ”). To modify a cycle that is already underway, press the button“ A ” , all of the settings will be cancelled. To set a new cycle, follow the instructions contained in the paragraph entitled “Switching the dishwasher ON”. B1 C1 C2 C3 C5 C6 A Moving the Appliance If the appliance must be moved, try to keep it in a vertical position. If absolutely necessary, it can be positioned on its back. Seals One of the ...

Herunterladen

Geben Sie zwei Ziffern: