Stimmen - 1, Durchschnittliche Bewertung: 4 ( )

Hersteller: Dacor Dateigröße: 1.09 mb Dateiname: Unterrichtssprache:

Do not install a damaged or incomplete appliance. Extended toe kick Left side access panel 6 Plastic fasteners (for access panel) Use and care manual Model ID24 only: Integrated template, screws and door tensioning springs for heavy door panels. A bottle of Dacor® Stainless Steel Cleaner is also included with models having stainless steel doors. Tools required for installation: Wire strippers Level Crescent wrench Phillips screwdriver Tape measure Materials required for installation (not provided): 2 wire nuts to fit wire mentioned above. Additional wire nuts may be required for connection to house wiring. 3/4” UL/CSA approved strain relief Hose clamp (for 1 3/8” OD drain hose) 3/8” flexible braided fill hose (required length varies) Wire or three-prong UL/CSA approved electric cord (see electrical specifications) A B C D E F G H J K L M N P Q N L M 24-Inch Integrated Custom Panel Installation A B C D E P Q F G H J K Make sure you have everything necessary for proper installation before proceeding. Installation Specifications Installation Specifications WARNING • • • • Do not install the dishwasher unless the electrical service provided meets the dishwasher specifications (see page 5). A qualified technician must complete the installation of this built-in appliance. The owner is responsible to make sure the dishwasher is properly installed. Improper connection of the electrical wiring may create an electric shock or fire hazard and may result in damage to the dishwasher’s electrical system. To avoid an electrical shock hazard, turn off power to the electrical outlet or junction box at the circuit breaker panel or fuse box before proceeding. Do not turn on the power or water supply until instructed to do so on the following pages. Do not allow any material, including the hoses or electrical wiring to be directly behind the dishwasher while pushing it into the cut-out opening. Carefully pull the slack out of both hoses and the wiring from outside the cut-out during push back to prevent pinching. An electric shock hazard or water damage may result from pinched wires or hoses. Damage due to improper installation is not covered under warranty. Electrical Connection 1. Make sure power to the electrical receptacle or junction box is off. 2. Before connecting the wiring and the plumbing, push the dishwasher into position with the back of the unit about six (6) inches in front of the cut-out. 3. Remove the two (2) screws that hold the toe kick assembly in place and remove it. NOtE: Do not reinstall the toe kick until the dishwasher is completely installed and tested. Toe kick assemblyRetaining screw, 2 places Door 4. Remove the dishwasher junction box cover screw. The junction box is mounted to the dishwasher chassis below the door. Screw Junction Box Location 5. Remove the junction box cover. 6. Install a 3/4” UL/CSA approved strain relief on the base of the dishwasher junction box. Junction Box Wiring Ground connection Strain relief Base Wire nuts 7. Strip the three (3) wires on the end of the electric cord or one end of the wire that will connect to the house wiring. 8. Feed the end of the wire or cord through the dishwasher chassis into the junction box base through the strain relief. 9. Loosen the grounding screw on the base and connect the green wire. Tighten it into place. 10. Connect the power cord (or house wiring) black and white wires to the black and white wires inside the junction box. Match the colors. Use wire nuts to connect them. 11. Tighten the strain relief. Pull gently on the wiring from the back to make sure it is secure. 12. Replace the junction box cover and screw. Installation Instructions Installation Instructions Electrical Connection (Continued) 13. Feed the electric wire or cord into the utility hole in the side of the cut-out. Pull all of the slack out of the wire. If the unit is to be connected directly to the house wiring: • With power turned off at the circuit breaker or fuse box, remove the house junction box cover. • Feed the dishwasher wiring into the junction box. Secure the wire with a UL/CSA approved strain relief. • Strip and connect the wires according to one of the wiring diagrams below. • Tighten the strain relief. Check to make sure the wire is secure. • Replace the junction box cover and screws. WARNING • • Connect the dishwasher ground wire to a separate, properly grounded wire installed by a licensed electrician. A grounded cold water pipe must have metal continuity to an electrical ground and must not be interrupted by insulating materials. Any insulating materials must be jumped with a length of No. 4 copper wire securely clamped to bare metal at both ends. See diagram below. To house circuit breaker panel or fuse box Feed the electric cord (or wire) and both hoses into the utility cut-out(s); direction varies with installation. Utility Cut-outs Hoses Wire or cord To house circuit breaker panel or fuse box Wire nut, 3 places Strain relief Junction box To dishwasher * D...

Herunterladen

Geben Sie zwei Ziffern: