Stimmen - 3, Durchschnittliche Bewertung: 3.3 ( )

Hersteller: Homelegance Dateigröße: 299.5 kb Dateiname: Unterrichtssprache:

Rinse with hot water. Drying. Normal Wash Light Wash (EN50242) Mixed Soups, potatoes, pasta, rice, eggs, roast or fried food. a little loosely attached Pre-wash use cold water. Extended wash at 50°C. Rinse with cold water. Rinse with hot water. Drying. Glass ware Coffee,cakes, milk, sausage, cold drinks, salads Very little loosely attached Wash at 45°C. Rinse with cold water. Hot rinse. Drying. Rapid wash Short wash at 40°C. Cold rinse. Soak Rinse off if the dishes have been stacked for several days in the dishwasher prior to washing. Short cold wash to prevent food residue from drying on the dishes . Delayed Start Detergent Rinse Aid Extended Wash Prewash 30g 7.5g 20g 5g 30g 7.5g 20g 5g 30g 7.5g (*) 20g 5g 15g 10g 15g 10g Laboratory measured valve in accordance with European Standard EN50242 Duration in minutes Energy consumption in kWh Water consumption in litres 112 1.62 18 94 1.48 16 102 1.24 15 90 1.15 14 170 1.10 16 142 1.00 13 92 1.12 12 82 1.10 10 31 0.40 9 29 0.30 8 12 0.02 3 12 0.02 3 * EN50242 test with rinse aid setting 5 Washing dishes Programme selection The most appropriate programme can be identified by comparing the type of crockery, cutlery, etc., as well as the amount and condition of food remains, with the details contained in the wash cycle table.The corresponding programme sequence, duration and consumption details are shown in the right half of the overview. For example: Use the« normal» programme for dishes and utensils which have plenty of food remains stuck on hard. Earn savings If only a small number of dishes have been loaded into the dishwasher,selecting a programme that operates at the next lowest temperature will usually be sufficient. Programme data The stated programme data are based on standard operating conditions. The values can vary considerably according to: different amounts of dishes temperature of mains water supply pressure of mains water supply ambient temperature fluctuations in mains voltage machine-related factors (e.g. temperature, water volume,...) Energy and water consumption is reduced by up to 1/4 when dishes are washed in the upper basket only.The water consumption values are related to water hardness level 1. Turbisensor* *on applicable models The Aquasensor ia an optical measuring device with which the cloudiness of the water in the dishwasher is measured. A photoelectric sensor is used to detect the degree of soiling in the water, caused by dissolved food particals such as egg, fat and rolled oats, etc. Switching the dishwasher ON Turn on the tap. Set ON-OFF button “ A ” to ON. All the programme indicators “J1,J2,J3,J4,J5,J6 ” light . Press programme button “I1” , programme indicator “ J1” blinks and the time-remaining indicator “ F ” displays the time of the programme.. If the door is closed, after 5 seconds, the programme indicator “ J1” bcomes to light and the dishwasher beeps one time , then the programme starts automatically. A I1 J1 J2 J3 J4 J5 J6 F End of programme Six beeps will indicate that the wash cycle has finished and all the programme indicators light. Switching the dishwasher OFF Several minutes after the programme has ended: Set main switch “A” to OFF. Open the door . Turn the water tap off. (Does not apply when Aquastop unit has been fitted) Remove dishes, etc. when they have cooled down. Interrupping the programme Open the door. Caution! There is a risk of water squirting out from inside the appliance. Do not open the door fully until spray arm has stopped rotating. When you open the door, the dishwasher will beep ten times every thirty seconds. If the appliance has already heated up or the hot water was switched ON and then the appliance door opened, leave the door ajar for several minutes and then close. Otherwise, the appliance door may open due to expansion. Delayed start programming You can delay the start of a programme in increments of one hour up to 12 hours. Switch dishwasher ON. Immediately press the Delayed Start button “ D ”, the delayed start indicator “ E ” blinks, the delayed start time indicator “ F ” changes to “ ”. Press the Delayed Start button “ D ” as many times as necessary until the numerical display shows the required delay. To cancel the time delay setting, pressing the Delayed Start button until the delayed start indicator “ E” goes out. E DF Press programme button “ I ” to choose the desired programme. I If the the door is closed, after 5 seconds the delayed start indicator “ E ” lights , the time-remaining indicator “ F ” will blink and decrease , the programme will start until the delayed start indicator “ F ” goes out . Cancelling or modifying a cycle A cycle that is underway can be modified if it has only been running for a short time. Otherwise, the detergent may have already been used, and the appliance may have already drained the wash water. If this is the case, the detergent dispenser must be refilled ( see the paragraph entitled, “ Loading the detergent ”). To modify a cycle that is already underwa...

Herunterladen

Geben Sie zwei Ziffern: