Stimmen - 3, Durchschnittliche Bewertung: 3.7 ( )

Hersteller: Fisher & Paykel Dateigröße: 4.3 mb Dateiname: Unterrichtssprache:

Rinse agent gives a streak free, sparkling clean look to glass and chinaware, in addition it prevents metal from tarnishing. The rinse agent dispenser is on the inside of each drawer, located underneath the detergent dispenser. The dispenser holds approximately 1.7 fl oz (50 ml) of rinse agent. Filling the rinse agent dispenser 1 Turn the plug counter-clockwise and remove. 2 Pour the rinse agent into the circular opening. 3 Take care not to spill rinse agent into the DishDrawer®. Any spillages must be wiped up to prevent excess foaming. Failure to wipe rinse agent spillages may result in a service call which will not be covered by warranty. 4 Fit the plug back into the original position. How much rinse agent to use The regulator may need adjusting to suit your water conditions. The lowest setting is ‘1’ and the highest is ‘5’. Refer to Option Adjustments section to adjust the rinse agent setting. If there is excessive foam at the end of the wash, reduce the setting. If dishes are wet or streaky after drying, increase the setting. Rinse agent indicator light If the rinse agent indicator light is red, refill the dispenser. If the rinse agent indicator light is dimly lit or not lit at all, there is enough rinse agent for the wash. Note: Lighter colored rinse agents will not dim the indicator light as effectively as darker colored rinse agents. When the rinse agent is being dispensed, you may notice some unusual noises during the wash, this is normal. US CA US CA Option adjustments 19 The following options can be adjusted to suit your preferences. Rinse Agent setting Reduce the Rinse agent setting if there is excess foam after a wash program. Increase the Rinse agent setting if dishes are wet or streaky after a wash program. Auto Power setting By default, DishDrawer® will automatically turn on whenever the drawer is opened. Washing will not start until the drawer is closed and the button has been pressed. If you do not want the DishDrawer® to turn on automatically, this feature can be turned off. End of Wash Program Beeps By default, DishDrawer® will beep six times at the end of a wash program. This feature can be turned off. Closed Drawer option The Closed Drawer option will lock the DishDrawer® when the drawer is closed. When you wish to open the drawer, press the button. When the drawer is fully closed again, the lid will automatically seal and lock after 30 seconds. If the Lock feature is used in conjunction with the Closed Drawer Option, pressing the button will not unlock the drawer. The Lock feature must be turned off to enable DishDrawer® to be opened. Note: this option is highly recommended if the DishDrawer is to be used in motor homes. How to make option adjustments End of Wash Program Beeps Closed Drawer Rinse Agent setting Auto Power option option option1 Follow the steps below First Enter Option Adjustment Mode1 Press the button to turn power on. Open DishDrawer. 2Press and hold the and buttons for 5 seconds until one long beep sounds. red / off purple / on blue / on red / on Make an adjustment The current setting is shownon the wash programselector in red lights. If fourred lights are lit, the optionselected setting is set to four. Press the button toincrease the setting. Press the button to turn the selected option on or off. Save Press the button to save the change. Example Rinse Agent setting set tofour OnOff OnOff OnOff US CA 20 Option adjustments The option sequence will start again from the Rinse Agent setting. US CA US CA User maintenance instructions 21 Cleaning the surfaces Important! We do not recommend the use of the following cleaning aids on/in your DishDrawer® as they may damage the surfaces: Plastic or stainless steel scouring pads Abrasive, solvent, household cleaners Acid or alkaline cleaners Hand washing liquids or soap Laundry detergents or disinfectants Proprietary ‘Stainless Steel’ cleaners or polishes as these may damage the protective coating. 1 Wipe with a clean damp cloth. Take care not to wet the control panel. 2 Dry with a clean lint-free cloth. 22 Cleaning the drain filter, spray arm and filter plate We recommend that the drain filter is cleaned whenever there is evidence of food particles. The spray arm and filter plate may need cleaning about once a month in normal use or more often should the need arise. If a dishwasher cleaner/descaler is used, you must run a wash program with detergent immediately afterward to prevent any damage to your DishDrawer®. Important ! The DishDrawer® must be used with the filter plate, drain filter and spray arm correctly in place. Cleaning the drain filter 1 Lift up the drain filter access panel on the basket (if fitted). 2 Lift and remove the drain filter. 3 Empty, rinse clean under running water and replace back into the allocated space. 4 Ensure the drain filter is flush with the filter plate. User maintenance instructions Internal parts of the DishDrawer® a Spray arm b Filter plate c Drain filter a b c US CA User maintenance instruc...

Herunterladen

Geben Sie zwei Ziffern: