Stimmen - 2, Durchschnittliche Bewertung: 4 ( )

Hersteller: Miele Dateigröße: 2.3 mb Dateiname: Unterrichtssprache:

,Only use detergents formulated for domestic dishwashers. Use only the recommended amount of detergent. Continued use of too much detergent may cause machine damage. Use Adding detergent ^ Add detergent to compartment II and close the flap. ^ If a Pre-rinse is desired, and available for your chosen program, add 1 teaspoon (5 ml) of detergent to compartment I. The horizontal marks in compartment II indicate the levels of approximately 1 . and 2 tablespoons (20 and 30 ml) respectively. Compartment I holds a maximum of 2 teaspoons (10 ml). ^To open, press the latch on the detergent dispenser. The flap will spring open. The flap is always open at the end of a program. Use Turning on ^ Make sure the spray arms can rotate freely. ^ Close the door. ^ Open the water supply, if it is closed. ^ Turn the dishwasher on s. The "Start/Stop" indicator flashes and the indicator of the last set program lights. Selecting a program Choose your program according to the type of load and soiling. The "Program guide" describes the programs and use. Starting a program ^ Select the desired program with the program selector button. The indicator of the selected program lights. ^ Press the "Start/Stop" button. The program starts. The indicators "Start/Stop", "Rinse" and the last selected program light. Cancel a program only in the first 5 minutes. Otherwise important program steps (e.g. the water softening) may be interrupted. Program sequence display After a program has been started the current stage of the program is indicated by the program cycle indicator. Program guide Program When to use Program sequence Prerinse 1 2 Main wash Interim rinse 1 2 Final rinse Drying Pots & Pans For normally soiled pots and pans with dried on food, also for heavily soiled dishware, use 120% of normal detergent dose x x x x x Normal For normally soiled dishware x x x x x x Economy For normally soiled dishware, energy saving program with a long soaking time and a low temperature x x x x SaniWash Extended wash time, for sanitizing normally soiled dishware with dried on food x x x x x Short "Quick program" for lightly soiled dishware, e.g. party dishware includes sensor controlled Glasscare, not suitable for detergent tabs x x x Rinse & Hold To rinse dishes when a complete program is not needed detergent is not recommended x Usage: Electric: 0.01 - 1.23 kWh Water: 1.3 - 6.3 gal (5 - 24 l) Use At the end of a program When the program has finished the "End" indicator lights. Dishes tends to chip if removed still hot from the dishwasher. ^ Let the dishware cool by opening the door slightly. The dishes will cool much faster. ^ Open the dishwasher and unload the dishes. ^ Turn the dishwasher off s. The dishwasher continues to use electricity until turned off with the s button. ^ If the dishwasher is not used for a longer period of time, e.g. vacationing, turn off the water supply. Interrupting a program A program is interrupted as soon as the door is opened. If the door is closed, the program will continue from where it was interrupted. ,Open the door with care. The water in the dishwasher is hot. Danger of scalding. Before closing the door again, leave it ajar for approx. 20 secs. This will enable the temperature in the wash cabinet to settle. Close the door firmly until it clicks into place. Changing a program If the detergent flap is already open do not change the program. If a program has already started and you wish to change it: ^ Press the "Start/Stop" button for at least one second. The program is cancelled. The "Start/Stop" indicator lights. ^ Select and start the desired program. Additional functions Factory default All settings can be reset to the factory default. ^ Turn the dishwasher off s. ^ Press the "Start/Stop" button and at the same time turn the dishwasher on s. Hold the "Start/Stop" button until the "Start/Stop" indicator comes on. If it does not come on, start over. ^ Press the program button 12 times. The bottom program indicator flashes once long and twice short in intervals. The "Rinse" indicator shows if a setting was changed. – The "Rinse" indicator flashes: All settings are the factory default. – The "Rinse" indicator is off: At least one setting was changed. ^ To reset the dishwasher to the default settings, press the "Start/Stop" button. ^ Turn the dishwasher off s. Frequently asked questions With the aid of the following guide, minor problems can be fixed without a service call. ,Repairs should only be carried out by a qualified and trained person in accordance with local and national safety regulations. Unauthorized repairs could cause personal injury or machine damage. Technical faults Issue Possible fault Solution The Start/Stop indicator does not flash after the dishwasher is turned on with s. The machine is not plugged in. Insert the plug. The fuse has tripped. Reset the circuit breaker. Make sure it is a 15 A breaker. The dishwasher stops during a program. The fuse has tripped. Reset the circuit breaker. Make sure it is a...

Herunterladen

Geben Sie zwei Ziffern: