Login:
Stimmen - 3, Durchschnittliche Bewertung: 4.3 ( )

Anleitung Mabe Canada, modell HDA1000

Hersteller: Mabe Canada
Dateigröße: 1.26 mb
Dateiname:
Unterrichtssprache:en
Link zum kostenlosen Download Hinweise finden Sie am Ende der Seite



Anleitung Zusammenfassung


Specify accessory number when ordering. 12 Before you call for service… ge.com Troubleshooting Tips Save time and money! Review the charts on the following pages, or visit ge.com. You may not need to call for service. Problem Possible Causes What To Do Dishwasher won’t run Fuse is blown, or the • Replace fuse or reset circuit breaker. Remove any other appliances circuit breaker tripped from the circuit. • Try pressing the START/RESET pad (Electronic models) two times. Power is turned off • In some installations, power to the dishwasher is provided through a wall switch, often located next to the disposer switch. Make sure it is on. Noise Some of the sounds • Soft food disposal shredding action. you’ll hear are normal • Drain valve opening to pump water out. • Timer control as cycle progresses. • Detergent cup opening. • The motor stopping during the drying period. • Water draining out of tub immediately after touching the START/RESET pad. Utensils are not secure • Make sure everything is secured in dishwasher. in rack or something small has dropped into rack Rattling dishes when • Make sure dishes are properly loaded. See the Loading the the spray arm rotates dishwasher racks section. Motor hums • Dishwasher has not been used on a regular basis. If you do not use your dishwasher often, set it to fill and pump out once every week. This will help keep the seal moist. Water standing in This is normal • A small amount of clean water around the outlet on the tub bottom the bottom of the tub at the back of the tub keeps the water seal lubricated. Water won’t pump Drain is clogged • If you have an air gap, clean it. out of the tub • Check to see if your kitchen sink is draining well. If not, you may need a plumber. • If the dishwasher drains into a disposer, run disposer clear. Suds in the tub Wrong detergent • Use only automatic dishwasher detergents to avoid sudsing. was used Cascade®, Cascade® Complete and Electrasol® Automatic Dishwashing Detergents have been approved for use in all GE dishwashers. • To remove suds from the tub, open the dishwasher and let suds dissipate. Add 1 gallon of cold water to the tub. On Models with a Dial: Close and latch the dishwasher. Pump out water by slowly turning the Dial until a drain period is reached. Repeat if necessary. On Models with Electronic Control: Pump out water by pressing the START/RESET pad, then 10 seconds later, press START/RESET pad again. Repeat if necessary. Rinse agent was spilled • Always wipe up rinse agent spills immediately. Stained tub interior Some tomato-based • Use of the RINSE ONLY cycle after adding the dish to the load foods can cause reddish can decrease the level of staining. GE recommends Cascade® stains Plastic Booster to help remove these types of stains. Tea or coffee stains • Remove the stain by hand, using a solution of 1/2 cup bleach and 3 cups warm water. WARNING Before cleaning interior, wait at least 20 minutes after a cycle for the heating elements to cool down. Failure to do so can result in burns. An overall yellow or • A special filter in the water supply line is the only way to correct brown film can be this problem. Contact a water softener company. caused by iron deposits in water White film on inside • GE recommends Jet-Dry ® or Cascade Crystal Clear® to help surface—hard water prevent hard water mineral deposits from forming. minerals • Run dishwasher with citric acid to remove mineral deposits. Citric acid (Part number: WD35X151) can be ordered through GE Parts. See back cover for ordering information. 13 Consumer SupportTroubleshooting TipsOperating InstructionsSafety Instructions Operating Instructions Safety InstructionsConsumer Support Troubleshooting Tips Before you call for service… Problem Possible Causes What To Do Dishes don’t dry Low inlet water temperature • Make sure inlet water temperature is at least 120°F. • Select HEATED DRY. • Use HOT START and ADDED HEAT options. • Select a higher cycle, such as POTS & PANS or HEAVY WASH. Rinse agent dispenser is em...

Dieses Handbuch ist für folgende Modelle:
Geräte - GHDA300 (1.26 mb)
Geräte - GSD1000 (1.26 mb)
Geräte - GSD2000 (1.26 mb)
Geräte - GSD3000 (1.26 mb)

Bewertungen



Bewerten
Vorname:
Geben Sie zwei Ziffern:
capcha





Kategorien