Stimmen - 4, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
Interrupting or Cancelling a dishwashing cycle Interrupt a dishwashing cycle that is in progress if it is absolutely necessary. Interrupting the dishwashing programme by opening the dishwasher door 1 Hot steam may escape when the door is opened. There is a risk of scalding. 1.Open the door carefully. The dishwashing cycle will stop. 2.Close the door. The cycle will continue. Cancelling the wash programme 1.Press function buttons 1 and 2 and hold them down. The LED indicators of all the programme buttons that can be selected will illuminate. 2.Release the function buttons. The wash programme has been cancelled. 3.If you want to start a new wash programme, check whether there is any detergent in the dispenser. 4.Switch off using the ON/OFF button. 3 Turning off the dishwasher will only interrupt a selected dishwashing cycle, not cancel it. The cycle will recommence after turning the dishwasher back on again. Setting the Delay Timer 3 With the delay timer you can delay the start of a dishwashing cycle for between 1 and 19 hours. 1.Press the Delay Timer button repeatedly until the multi-display shows the desired time delay, for example 12h, if the cycle is to start in 12 hours. The Delay Timer indicator is illuminated. 2.Select dishwashing cycle. 3.The time remaining to the start of the cycle is continuously displayed (e. g. 12h, 11h, 10h, … 1h etc.). To change the time delay: As long as the cycle has not yet started, you can still change the setting by pressing the DELAY TIMER button. Cancelling the time delay: Press the Delay Timer button repeatedly until the length of the selected cycle appears in the multi-display. The selected dishwashing cycle will begin immediately. To change a dishwashing cycle As long as the cycle has not yet started, you can still change the dish- washing cycle. First cancel the dishwashing cycle, then re-set the time delay, lastly select the new dishwashing cycle. Switching Off the dishwasher Only switch the dishwasher off when the multi-display indicates “0” for the cycle time remaining and the end of programme indicator is illuminated. With some dishwashing cycles, the drying fan continues to run even after the end of the cycle. 1.Press the ON/OFF button. All display indicators will go out. 2.Turn off the water tap. 1 Carefully open the door. Hot steam may escape. Hot dishes are sensitive to knocks. Therefore leave the dishes to cool for about 15 minutes before removing them. You also get a better drying result. Removing the Dishes 3 It is normal for the inner door and the dispensers to be damp. • Empty the lower basket first, then the upper basket. This way you avoid dripping water from the upper basket onto dishes in the lower basket. Care and cleaning 1 Do not use furniture care products or aggressive cleaners. • When necessary, clean the dishwasher’s controls with a soft cloth. • Occasionally check the internal dispensers, door seal and water inlet filter (if fitted) for dirt and clean them, if necessary. Cleaning the filters 3 The filters must be regularly checked and cleaned. Dirty filters will spoil the wash results. 1.Open the door and remove the lower basket. 2.Turn the handle about . of a turn anticlockwise (A) and remove the filter system (B). 3.Grasp the grip hole on the fine filter (1) and remove it from the micro-filter (2). 4.Clean all filters thoroughly under running water. 5.Remove the flat filter (3) from the base of the washing compartment and clean both surfaces thoroughly. 6.Re-insert the flat filter. 7.Place the fine filter in the micro-filter and fit the two together. 8.Insert the filter system in place and lock it by turning the handle clockwise as far as it will go. Ensure that the flat filter does not protrude above the base of the washing compartment. 1 Under no circumstances may the dishwasher be used without its filters. Cleaning the spray arm jets Regularly check the jets in the spray arms for blockages. When cleaning is necessary, remove spray arm from the fixture and clean jets with a pointed object (wire or needle). Then rinse out the spray arm using a strong jet of water. 3 Do not damage the jet opening. Upper basket spray arm 1.To remove upper basket spray arm, tilt it down hard. 2.Clean spray arms jets. 3.Place cleaned upper basket spray arm back in position against the connecting piece: press the two together firmly, until you feel them snap into place. Bottom spray arm 1.To remove bottom spray arm, pull it upwards out of its catch. 2.Clean spray arm jets. 3.Place bottom spray arm back in position against connecting piece and press down firmly, until you feel it snap into place. What to do if... Remedying small malfunctions If one of the following fault codes is displayed in the multi-display during operation: – Fault codeA10 (Problems with water inlet), – Fault codeA20 (Problems with water drainage), please have a look at the following table. When the fault is remedied, press the button for the cycle that has started. The cycle will continue. W...