Stimmen - 3, Durchschnittliche Bewertung: 3.7
(
)
)
|
Anleitung Zusammenfassung
3) The consumption figures were determined under standard conditions. They are intended as a guide only and depend on the loading. For this reason figures may vary in practice. Operating Instructions Starting the Wash Programme 0 1. Check that the dishes and cutlery are loaded into the dishwasher in such a manner that the spray arms are free to rotate. 2. Open the tap fully. 3. Close dishwasher door. 4. Turn the programme switch clockwise to A, or B or C (see „ Programme Table“). 1 For interference suppression reasons, only operate the programme switch with the dishwasher switched off. It is also possible that the automated addition of detergent will be triggered. 5. Turn the programme selector to the required programme (see „ Programme Table“). Power indicator light illuminates. The selected wash programme starts. The programme switch rotates during the wash programme and indi cates the position that has been reached in the programme. 1 If a wash programme has been started even though the tap was closed, turn the programme selector to the I position, open the tap and start the programme again. Changing/Interrupting the Wash Programme 3 Only change or interrupt a wash programme in progress if it is absolutely necessary. When the appliance is closed again, the air that has entered is heated rapidly and expands. This can cause water to escape onto the floor and possibly trigger the anti-flood system. Changing the wash programme 0 1. Turn the programme selector to the I position. Power indicator light goes out, wash programme stops. 1 Hot steam can escape when the door is opened. There is a risk of scolding! Open the door carefully. 2. Open dishwasher door and check whether there is still detergent in the container. Refill the container if necessary. 3. Close dishwasher door. 4. Turn the programme switch clockwise to A, or B or C (see „ Programme Table“). 5. Turn the programme selector to the required programme (see „ Programme Table“). Power indicator light illuminates, wash programme starts. Operating Instructions Interrupting the wash programme by opening the door of the dishwasher 1 Hot steam can escape when the door is opened. There is a risk of scolding! Open the door carefully. 0 1. Open the door of the dishwasher. The wash programme stops. 2. Shut the door. The wash programme continues. Switching Off the Dishwasher When the wash programme is finished: 0 1. Turn the programme selector to the I position. Power indicator light goes out. 1 Hot steam may escape if the door is opened immediately after the end of the programme. Therefore: 2. Open the door carefully. Emptying the Dishwasher • Hot dishes are sensitive to knocks. The dishes should therefore be 3 allowed to cool down before removing them from the appliance. • Leave the dishes in the dishwasher for approx. 15 minutes after the end of the programme so that they dry better and can cool down. • Empty the lower rack first, then the upper rack. In this way you will avoid any water left on the upper rack dripping onto the dishes in the lower rack and causing water spots. Care and Cleaning 1 Do not under any circumstances use furniture care products or aggressive cleaners. • If necessary, clean the controls only with a soft cloth and pure warm water. • Occasionally check the internal containers, door seal, and water inlet for soiling, clean if necessary. Operating Instructions Cleaning the Filter 3 The filters in the base of the washing compartment are to a large extent self-cleaning. Nevertheless the filters should be checked and cleaned from time to time. Dirty filters will degrade the washing result. 0 1. Open the door, remove the lower rack. 2. The dishwasher filter system comprises a coarse/fine filter, microfilter and a flat filter. Unlock the filter system using the handle on the microfilter, and remove. 3. Turn the handle about . a turn anti- clockwise and remove. 4. Take hold of the coarse/fine filter (1) by the handle with the hole and remove from the microfilter (2) 5. Clean all filters thoroughly under running water. 6. Remove the flat filter (3) from the base of the washing compartment and clean both faces thoroughly 7. Put the flat filter back in the base of the washing compartment 8. Place the coarse/fine filter in the microfilter and press together. 9. Put the filter combination in place and lock by turning the handle clockwise to the stop. During this process ensure that the flat filter does not protrude above the base of the washing compartment. 1 Under no circumstances may the dishwasher be used without filters. Operating Instructions What to do, when ... Try to rectify minor faults on the dishwasher with the aid of the instructions given here. If you call in customer service to resolve one of the malfunctions listed here, or rectify an error made in the operation of the appliance, the customer service engineer’s visit is not free of charge, even during the period of guarantee. ...there are problems with the operation of the dishwasher...