Stimmen - 1, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
25 Pre-Wash Summary Pre-Wash Summary The "Pre-Wash" program is a convenience feature that allows dishes to be rinsed, when you don't have a full load ready to be washed. (this prevents foods from becoming dried/caked on the dishes) It is not necessary to add detergent during the Pre- Wash cycle. It is important to make sure the incoming water is hot. Open the hot water faucet and run till hot, before connecting the dishwasher. NOTE: At the beginning of all programs, the dishwasher starts in "drain" mode. The drain pump always retains a small amount of water (in the sump) from the previous cycle. This is necessary to keep the pump primed. Don't be alarmed if you see small amounts of water being pumped-out from the drain hose prior to the start of the cycle, and/or water remaining in the sump area at the end of the cycle. (THIS IS NORMAL) Sani/Econo Summary The "Sani" feature utilizes a heating element to boost (increase) temperature of the wash water upto 160°F (71°C). To activate this feature, push the "Sani/Econo" button on the control panel. • The red indicator light adjacent to the button illuminates, indentifying the Sani feature is selected. To deactivate the Sani feature, push the “Sani/Econo” button again and the indicator light turns off. • If you elect to use the “Econo” feature, (no indicator light) dishes are washed using standard (household) hot water only. We recommend a minimum (household) water temperature setting of 120°F (49°C) otherwise washability may be compromised. SPECIAL NOTE: During the final rinse cycle of the NORMAL/SHORT/RINSE programs, the heating element is activated automatically, irregardless of the “Sani/Econo” setting. This feature provides optimum conditions for dispursement of the rinse agent and accelerates the drying time of the dishes. PROGRAM SUMMARY PRE-WASH (ECONO MODE) Water Temperature: (Household Temperature) Program: 1 Rinse Cycle Water Consumption: 3.0 liters / 0.79US/gal. Length of Program : 6min. NORMAL WASH (ECONO MODE) Water Temperature: (Household Temperature) Program: 2 Wash & 2 Rinse Cycles Water Consumption: 12.0 liters / 3.2US/gal. Length of Program : 42 min. SHORT WASH (ECONO MODE) Water Temperature: (Household Temperature) Program: 1 Wash & 2 Rinse Cycles Water Consumption: 9.0 liters / 2.4US/gal. Length of Program: 29 min. NORMAL WASH (SANI MODE) Water Temperature: 160°F (71°C). Program: 2 Wash & 2 Rinse Cycles Water Consumption: 12.0 liters / 3.2US/gal. Length of Program: 47min. SHORT WASH (SANI MODE) Water Temperature: 160°F (71°C). Program: 1 Wash & 2 Rinse Cycles Water Consumption: 9.0 liters / 2.4US/gal. Length of Program: 29min. RINSE (SANI/ECONO) IDEAL FOR GLASSWARE Water Temperature: (Household Temperature) Program: 2 Rinse Cycles Note: the 1st cycle can be used as a wash cycle. Water Consumption: 6.0 liters / 1.6US/gal. Length of Program: 20min. NOTE: During the 1st cycle of the RINSE program, the “sani” feature is not activated, irregardless of the “SANI/ECONO” setting. 6 OPERATING INSTRUCTIONS OPERATING INSTRUCTIONS Make sure all hose connections are solid and no leaks are detected before stating the dishwasher. Front Door: To open the door, push the door release button and the door will (partially) open automatically. Pull the door down to open fully. Loading Detergent (Automatic Dispenser): To open the “A” cover on the dispenser, press the ‘B” button. Add the recommended amount of detergent into the “C” compartment. Close the cover and press down until it clicks (locks) in place. (See Fig. A ) Fig. A Rinse Agent: Unscrew cap and pour the recommended amount 59ml (2 fl oz liq) into the dispenser. Avoid overfilling. Load Dishes: Pull the rack all the way out until it comes to a stop on the door. Load dishes with the soiled surface facing toward the center of the tub. (see page 5 for reference) To facilitate loading the large dinner plates, it will be necessary to remove the silverware basket from the rack. When loading is complete return silverware basket to original position. Load Silverware: Silverware should be placed in basket with the handles at the bottom. To avoid cut type injuries, exercise caution when (handling) loading/unloading sharp objects. When loading is complete, slide the dish rack back into the tub. Close Door: Lift the door and push firmly to close. Listen for positive door lock (click) when the door is closed. Selecting Program: Always make sure the power on/off button is “off” before selecting a program. Rotate the timer dial (clockwise) until the dot on the timer dial is aligned with the program you want to use. Select Sani/Econo Mode: Push the Sani/Econo button on the control panel. When the push button is “in” you have selected the “Sani” mode. When the push button is ”out” you have selected “Econo” mode. The “red” pilot light adjacent to the push button illuminates (only) when you select ‘Sani” mode and the power is turned on. Starting the Dishwasher: Only after all program settings are made should you start the di...