Stimmen - 4, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
Connecting the Portable/Convertible Dishwasher 1. Run water at faucet until it is hot. Turn off faucet. 2. Pull hoses out of compartment. 3. Push collar down and slip faucet connector onto faucet adapter. 4. When connector snaps into place, release collar. 5. Slowly turn on hot water all the way. 6. Plug power cord into grounded outlet. 12 Connecting and Disconnecting the Portable/ Convertible Dishwasher (continued) Getting Water While Dishwasher is Running You can get water from the faucet while the dishwasher is connected. However, avoid getting water when the dishwasher is filling or draining. 1. Press red button on coupler to get the water you want. The faucet is set on hot, adjust faucet if you want cold. 2. Be sure hot water is turned back on all the way to complete cycle. Disconnecting the Portable/ Convertible Dishwasher 1. When cycle has finished, turn off hot water. 2. Press red button on coupler to release water pressure being careful not to release coupler. 3. Press down on collar to release coupler. 4. Empty remaining water from coupler and return it to compartment. 5. Unplug power cord and return it to compartment. IMPORTANT: A sink spray attachment hose can burst due to constant water pressure while in use. If your spray hose is installed on same water line as the dishwasher, we suggest you disconnect the sink spray attachment and plug the hole. Fire Hazard/Electrical Shock Do not use an adapter plug, extension cord or remove grounding prong from electrical power cord. Failure to follow this warning can cause serious injury, fire or death. Electrical Connection for a Portable/ Convertible Dishwasher An electrical supply of 120 volts, 60 Hz, AC only, 15 amps is required. For your safety, the dishwasher must be grounded. If there is a malfunction or breakdown, grounding will reduce risk of electrical shock. This dishwasher has a power cord with a 3-prong grounding plug. It must be plugged into a mating 3-prong grounding type receptacle, installed and grounded in accordance with the National Electrical Code and any local codes and ordinances. Grounding type wall receptacle Do not under any circumstances cut, remove or bypass the grounding prong from this plug. Power supply cord with 3-prong grounding plug Converting to Built-In Your portable dishwasher can be converted to a built-in (undercounter) model. A conversion kit No. 154241302 is required and is available from your local dealer or distributor. Instructions are included with the kit. 13 Changing Color Panels Cut Hazard Metal door panels are sharp and should be handled with care. Wear gloves to protect hands. Failure to do so can result in injury. 3. Grasp top of upper panel(s) and pull up until clear of divider trim strip. Then bow panel(s) until clear of side trim. Remove panel(s) but do not remove spacer. Note: To complete color panel change on units without a divider trim strip, proceed with steps 5, 6 and 8. Divider trim strip Spacer Bottom trim Bottom edge of door Some models come with reversible door panel inserts which offer three decorative colors. The panels are separated by a divider trim strip. Depending on the model, either or both panels may be changed. To change the color panel: Note: If your unit does not have a divider trim strip, exceptions to these directions are noted after the individual steps. 1. Remove snap-on bottom trim by pulling forward. Support door panels by pressing in gently while removing trim. Note: After trim is removed, check bottom edge of door for reference when replacing later. 2. With one hand on the upper panel and one hand on the lower panel, gently slide the 4. Check to see if spacer has remained in panel assembly down until the entire the channel of the divider trim strip. If it assembly rests on the floor. Note: Slide has not, replace securely in channel. It color panel(s) down about 1/2" on units may be helpful to gently push in on divider without a divider trim strip. trim strip while reinserting the spacer. 14 Changing Color Panels (continued) 5. Arrange panel(s) so the desired color is facing out. Place one side of panel(s) under side trim and bow slightly until other side fits under opposite trim. Push down to make sure panel(s) and spacer are in channel of divider trim strip. 6. Move complete panel assembly up by pushing from sides and bottom of lower panel. Check to make sure the color panel(s) fit securely under control panel by pressing in at top of color panel(s). Control panel Changing Color Panels (continued) 5. Arrange panel(s) so the desired color is facing out. Place one side of panel(s) under side trim and bow slightly until other side fits under opposite trim. Push down to make sure panel(s) and spacer are in channel of divider trim strip. 6. Move complete panel assembly up by pushing from sides and bottom of lower panel. Check to make sure the color panel(s) fit securely under control panel by pressing in at top of color panel(s). Control panel 7. To change lower panel, use one ...