• Selma, AL 36703 (334) 874-2700 Parts Ordering 1-800-304-2836 Fax 1-800-572-1784 BUSH HOG / MATERIAL HANDLING REPAIR PARTS MANUAL SEPTEMBER, 2006 3045 MID-MOUNT LOADER ALPHABETICAL INDEX CONTENTS PAGE Bucket Assemblies....................................................................................................................................1-20D-1 Exhaust Relocator Kits................................................................................................................

DITCH SOIL PILE Leave dirt which drifts over the side of the bucket for final clean-up. DITCH Pile dirt on the high side for easier backfilling on a slope. 20 HANDLING LARGE HEAVY OBJECTS WARNING Do not use front end loaders for handling large heavy objects such as logs or oil drums. Handle large round hay bales only when loader is equipped with Bush Hog Bale Spear Attachment. Handling large heavy objects can be extremely dangerous due to: Possibility of rolling the tractor over. Possibility o

5. During operation, listen for abnormal sounds which might indicate loose parts or other damage. AFTER EACH USE 1. Clean all debris from machine, especially cylinder rods and affixed safety decals. Replace any missing or illegible decals. 2. Inspect loader for worn or damaged components. Repair or replace before next use. Any replace- ment components installed during repair shall include the components’ current safety decals specified by the manufacturer to be affixed to the component. 3. Store

1530 lbs. 2900 lbs. VV. Rollback Force at Maximum Height 31.5” Forward of Pivot Pin 1935 lbs. 1625 lbs. 2300 lbs. XX. Rollback Force at 59” Height 31.5” Forward of Pivot Pin 2300 lbs. 2020 lbs. 3400 lbs. ZZ. Rollback Force at Ground Level 31.5” Forward of Pivot Pin 1700 lbs. 1680 lbs. 2800 lbs. Raising Time - Ground Level to Full Height 3.5 sec. 3.8 sec. 5 sec. Lowering Time - Full Height to Ground 2.5 sec. 2.3 sec. 3 sec. Bucket Dumping Time -Full Rollback to Full Dump 4.0 sec. 3.3 sec. 4 sec.

3. If parts not made or supplied by Bush Hog have been used in connection with the unit, if, in the sole judgement of Bush Hog such use affects its performance, stability or reliability. 4. If the unit has been altered or repaired outside of an authorized Bush Hog dealership in a manner which, in the sole judgement of Bush Hog, affects its performance, stability or reliability. 5. To normal maintenance service and normal replacement items such as gearbox lubricant, hydraulic fluid, worn blades,

3600 lbs. 3750 lbs. 3840 lbs. Raising Time - Ground Level to Full Height 5 sec. 5 sec. 5 sec. 9 sec. Lowering Time - Full Height to Ground 4 sec. 3 sec. 3 sec. 6 sec. Bucket Dumping Time - Full Rollback to Full Dump 5 sec. 5 sec. 5 sec. 6 sec. Bucket Rollback Time - Full Dump to Full Rollback 3 sec. 3 sec. 3 sec. 4 sec. Tractor HP Range 40 - 60 2 & 4 WD 40 - 70 2 & 4 WD 60 - 90 2 & 4 WD 70 - 110 2 & 4 WD Based On Tractor Hydraulic System: Pressure Flow 2850 psi 11 gpm 2850 psi 11 gpm 2850 psi 16

Figure 2-12 Tractor Backed Away From Loader SECTION III OPERATING INSTRUCTIONS 3-1 GENERAL SAFETY Only qualified people familiar with this operator’s manual should operate this machine. Operator should wear hard hat, safety glasses, and safety shoes. The operator should read, understand and practice all safety messages shown on the caution, warning and danger decals affixed to the loader to avoid serious injury or death. It is recommended that tractor be equipped with Rollover Protective System

Crate 50051729 CABLE CONTROL VALVE KIT PART NUMBER QTY. ...... 1........... ...... 1........... ...... 1........... ...... 1........... ...... 2........... ...... 1........... ...... 1........... ...... 2........... ...... 2........... ...... 1........... ...... 1........... ...... 1........... ...... 1........... ...... 1........... PART NAME 50051669.................50051670.................50051671.................50051672.................50041057.................50041068.................5002

Attach the support tube to the support mount as shown in Fig. 1. (NOTE: Take care to not cut cable covering on sharp edges and be sure cable routing will not cause binding when attached to the valve). 9. Tighten all fasteners for handle controls and apply control decal to plate atop the support tube (Refer to Fig. 1). 10. ATTACHING VALVE TO LOADER FRAME: Attach the valve mount to the outside surface of the pedestal on the mounting bracket of load on right hand side of the tractor. Use the 1/2” x

All operations should be conducted within the loader limits specified in Technical Specifications. 7 Model 3860 QT Technical Specifications G E J C B A H F D G E J C H F D A. Maximum Lift Height - Measured at Pivot Pin . . . .176" B. Maximum Lift Height - Under Level Bucket . . . . . 170" C. Clearance with Attachment Dumped 45. . . . . . . . 148" D. Reach at Maximum Height . . . . . . . . . . . . . . . . . . . . 33” E. Maximum Dump Angle . . . . . . . . . . . . . . . . . . . . . . . 34° F. Reach