Stimmen - 4, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
When removing, changing the angle, or reversing the rake, be sure that your feet are never under the rake. Use extreme caution when backfilling deep holes or trenches. Be careful to avoid catching the rake on stumps or other immovable objects. Use care when working on slopes. Avoid excessive speed during operation. Make adjustments only when the implement is attached to the tractor. When using the rake in a reverse position, use extra care. Do not ram rake into piles of dirt. Tractor lift arms and the rake are not built to take high impact loads in this position. Ramming backwards can also dislodge operator from seat and/or tractor controls, resulting in possible serious injury or death. Always ease the tractor into the load. It may be necessary to reposition and take less “bite” on the material to move it safely. Operating spring steel rake tines may suddenly fling rocks and clods. Keep all bystanders 50 feet away and operator must wear safety glasses. Watch for and avoid hidden obstructions, i.e., buried pipes, rocks, concrete piers, uneven concrete slabs, stumps, etc., when operating. Stop power unit and equipment immediately upon striking an obstruction. Turn off engine, remove key, inspect, and repair any damage before resuming operation. Before leaving operator’s seat, lower lift arms and put attachment on the ground. Engage brake, stop engine, remove key, and remove seat belt. Never perform service or maintenance with engine running. 5 SAFETY SIGNS . Keep children away from danger all day, every day. . Please work, drive, play, and live each day with care and concern for your safety and that of your family and fellow citizens. OBEY ALL SAFETY WARNINGS!! 6 INSTRUCTIONS TRACTOR REQUIREMENTS AND PREPARATION —————————————————— The DCR, MCR, and LRHD Series Landscape Rakes will fit most Category I) tractors equipped with a standard 3 point hitch. DCR Series rakes will also fit Category 0 hitch tractors. NOTE: Some Category 0 tractors have very short lift arms or 5/8” diameter (Cat. 0) lift arm ball ends. The DCR Series rakes will fit these tractors if equipped with special Cat. 0 pullpins. The pins need to be installed to the inside of the 3 pt. frame. Check the tractor’s 3 point hydraulic lift system. It should operate up and down smoothly and hold its position when set. Refer to your tractor owner’s manual or dealer for any adjustments necessary to put the 3 point hydraulic lift system in good working order. (I&T shop manuals will list most specifications and adjustment instructions – available from most farm equipment dealers.) Tractor should be equipped with stabilizer bars, adjustable sway chains, or sway blocks to keep the implement from swinging side to side. Smaller size tractors may need front counter weights to counter-balance the weight of the implement. WARNING! Power unit must be equipped with ROPS or ROPS cab and seat belt. Keep seat belt securely fastened. Falling off power unit can result in death from being run over or crushed. Keep foldable ROPS systems in “locked up” position at all times. CAUTION! Be sure your tractor and loader is in good condition. Read all the safety precautions and make sure all equipment operators are familiar with the safety rules of operation. The operator is responsible for the safe operation of this equipment. The operator must be properly trained. Operators should be familiar with the tractor and attachment, and all safety practices before starting operation. Read the safety rules and safety signs on pages 3-6. PACKAGING —————————————————— The landscape rake is shipped as two bundles: 1. Main Frame with pull pins, bolts and nuts. 2. Rake Tine Bar Assembly (Teeth installed). ASSEMBLY AND MOUNTING —————————————————— Preview the assembly instructions and the exploded view of the landscape rake in your operator’s manual and become familiar as to how the parts or assemblies go together. Select an area for assembly that is clean and free from debris. The two main subassemblies of the landscape rake are heavy and awkward to handle. It is recommended that you have one or two helpers to complete the assembly. 1. On DCR and MCR models, assemble the “A” frame as shown in the exploded parts view (pg. 12 or pg. 13). 2. It is suggested that you mount the main frame on the 3 point hitch of your tractor before assembling the landscape rake as follows: a. Lower the 3 point hitch on your tractor to facilitate mounting of the main frame of the rake to the tractor. b. Insert the lift arm pins on the main frame into the ball sockets in the lift arms of the tractor 3 point hitch. Pin in place with linchpins (not furnished). NOTE: On DCR models – if your tractor has a Category 0 3 p...
Dieses Handbuch ist für folgende Modelle:Gabelstapler - DCR-4 (231.32 kb)
Gabelstapler - LRHD-6 (231.32 kb)
Gabelstapler - LRHD-7 (231.32 kb)
Gabelstapler - MCR-6 (231.32 kb)