Stimmen - 1, Durchschnittliche Bewertung: 5
(
)
)
|
Anleitung Zusammenfassung
Simple, reliable, accurate…it allows you to monitor indoor or outdoor locations from one room. The base unit reads indoor conditions, while the remote sensor wirelessly reports outdoor weather conditions back to the base unit for an all-in-one weather display. Plan your work day, play day, every day. Now that’s smart! Table of Contents Powering theWeatherGuide™..................................................................3 How to Set Up the WeatherGuide™ ......................................................3 How to Display the WeatherGuide™ ......................................................5 How to Read theWeatherGuide™..........................................................6 Temperature Displays ................................................................7 Minimum/Maximum Records....................................................8 Temperature Trends....................................................................9 °F/°C Switch ................................................................................9 Low Battery Display ..................................................................9 TroubleShooting Disconnected Signals................................................................10 Transmission Collision ............................................................11 Problem Solving ........................................................................11 Precautions ................................................................................12 2 To Power your WeatherGuide™ Base Unit Your WeatherGuide™ base unit is powered by 2 AAA batteries (not included). Remove the battery compartment cover located on the back of the unit. Install 2 AAA batteries. Replace the battery compartment cover. Important: Power the base unit before installing batteries in the remote sensor, or the units’ transmissions may not properly connect. Remote Sensor Unscrew the 4 screws securing the remote sensor’s battery compart- ment cover located on the back of the unit. Install 2 AAA batteries. (Tip: Lithium batteries are recommended in extremely cold or hot lo- cations.) How to Set up Your WeatherGuide™ System First, power up the base unit, using 2 AAA batteries. Next, install 2 AAA batteries into the remote sensor. Place the base unit as close as possi- ble to the remote unit. MovechannelswitchtoChannel1 Press the Tx button to send transmission signal to base unit There is a Channel switch in the remote sensor battery compartment. Move the switch to Channel 1. Press the “TX” button located inside the remote sensor battery compartment.This will send a transmission signal to the base unit.The red LED Indicator light will flash when a signal is transmitted. 3 If the transmission is successful,the remote sensor readings and a icon will appear on the base unit. If dashes are still displayed on the receiver unit, press the Tx button again. Transmission successful Replace the remote’s battery compart- ment cover. The remote will automatically transmit readings to the base unit. • The first remote registered will transmit every 53 seconds. • If a second remote is registered, it will transmit every 56 seconds. • If a third remote is registered, it will transmit every 59 seconds. Note: A maximum of 3 remote sensor units can be registered. Should you purchase one or two additional remote units (Model 1534, sold separately) to expand your thermometer monitoring capabilities to multiple locations, slide the CH switch to Channel 2 to register the second sensor and select Channel 3 to register the third sensor.The Channel number assigned will appear on the base unit’s LCD screen. 4 How to Display your WeatherGuide™ Table top – use the Table Stand on the back of the base and remote sensor units Wall – use the keyhole on the back of the base and remote sensor units. KeyholeTableStandBaseUnitRemoteSensor Base unit location – Place the unit indoors in a well-ventilated location away from direct sunlight. Remote sensor location – The transmission range of the remote sensor is 100 feet.The effective transmission range is vastly affected by obstacles such as walls, sheds, trees, etc.Try various set ups for the best results. Shorten the distance between receiver and remote units when necessary. Place indoor in a well ventilated location away from direct sunlight. Place the sensor in a dry, shaded area. Direct sunlight will heat the casing and inflate temperatures readings. Important: Though the remote unit is weather proof, it should be placed away from direct sunlight, rain, snow and should never be submerged in water. A maximum of 3 remote sensor units can be registered. One remote sensor is included.To purchase additional Remote Sensors (Taylor model 1534), please visit 5 How to Read Your WeatherGuide™ The base unit displays indoor conditions from its location. The remote unit will transmit weather readings from its location back to the base unit. Alternately, the remote sensor’s probe cord may b...