Stimmen - 3, Durchschnittliche Bewertung: 4.3
(
)
)
|
Anleitung Zusammenfassung
Indoor temperature readings – these are temperatures at the base unit’s location. Outdoor temperature readings – these are temperatures that are measured by the remote sensor. Indoor humidity readings – these are temperatures at the base unit’s location. Outdoor humidity readings – these are temperatures that are measured by the remote sensor. Press the T/H button to switch between temperature and humidity displays. 12 PressandholdMax/Mintoresethigh/lowtemperatureor Current readings Press MIN/MAX to see highand low daily temperature & humidity Minimum or Maximum readings Back to current readings Minimum or Maximum readings on screen ToView Minimum/Maximum temperature/humidity readings Your WeatherGuide™ will store the last recorded high and low temperatures andhumidity levels over a 24 hour period.The24 hour period starts when the batteriesare installed. 1. Press the “Min/Max” button once to see the highest temperature/humidity of the day. 2. Press the “Min/Max” button again to see the lowest temperature/humidity of the day. 3.Press the “Min/Max” button a third time to see current temperature/humidity again. To Clear the minimum or maximum read- ings, press and hold the “Min/Max” button while those readings are on the screen.The reading will reset to the current tempera- ture. Min/Max readings are cleared. humidity 13 Temperature Trend Indicators Your WeatherGuide™ will indicate if temperatures are rising, falling, or steady. indicates Rising Temperatures readings (temperatures have gone up more than 2 degrees in an hour) indicates Steady Temperature readings indicates Falling Temperatures (tempera- tures have gone down more than 2 degrees in an hour) Temperature trending up Humidity Trend Indicators Your WeatherGuide™ will indicate if humidity levels are rising, falling, or steady. indicates Rising Humidity readings (humid- ity has gone up more than 2 degrees in an hour) indicates Steady Humidity readings indicates Falling Humidity (humidity has gone down more than 2 degrees in an hour) Humidity trending up 14 12-24 Hour Weather Forecast YourWeatherGuide™ will estimate weather conditions over the next 12 to 24 hours.These estimates are based on altitude and changes in barometric pressure. Weather Icons One of these weather icons will appear at the top of the display: Sunny Stormy Becoming Cloudy Snowy Cloudy Snowstorm Rain 15 Backlight Feature The base unit has a backlight for easy viewing of the screen. Press the “Snooze/Light” button to turn the backlight on for 3 seconds. Press SNOOZE/LIGHT for a 3 second backlight To Switch Between °F and °C Press the “+C/F” button to switch between Fahrenheit and Celsius temperature dis- plays. Press +C/F to switch between °F&°C Low Battery Indicator A on the LCD indicates the batteries are running low and should soon be replaced. -A by the indoor temperature display indicates the base unit bat- teries are low. -A on the remote sensor indicates the remote batteries are low. Base Unit Baseunitbatterieslow RemoteSensorRemotesensorbatterieslow 16 Trouble-Shooting Disconnected Signals If the receiver unit does not receive a transmission from a remote chan- nel for 1 hour, the display will show dashes.To correct this problem: 1. Check that the remote is properly positioned, within the appro- priate transmission range. Transmissions are vastly affected by building materials and where the receiver and remote units are positioned.Try various set ups for the best results. Shorten the distance between receiver and remote units when necessary. 2. Check to make sure the transmission path is clear of obstacles and interference. 3. If new batteries are faulty on the initial installation, install fresh batteries. If you did not notice the Low Battery icon warning and the product performed correctly after initial set up, the batteries have lost their charge. Replace batteries (see the Power Sources section of this manual.) 4. Press the “Tx” button in the battery compartment of the remote to send a transmission signal to the base unit. 5. Press and hold the “Channel” button on the back of the base unit. This will clear the channel setting and the base unit will begin searching for remote sensor transmissions. Press the “Tx” button in the battery compartment of the remote to send a transmis- sion signal to the base unit. 6. Please note that below 32.F / 0.C the LCD readout on the re- mote unit may begin to fail display.When this happens the remote will still transmit correct temperature readings to the receiver unit but will not appear on the remote LCD.When the tempera- ture rises above 32.F / 0.C the display will begin to function nor- mally again. 17 Transmission Collision Signals from other household devices, such as doorbells, home security systems and entry controls, may interfere.This is normal and does not affect the general performance of this product.The transmission will resume once the interference recedes. Note: This equipment has been tested and found to comply with the l...