Stimmen - 4, Durchschnittliche Bewertung: 3.3
(
)
)
|
Anleitung Zusammenfassung
If you experience difficulty during the installation, contact Garmin Product Support or seek the advice of a professional installer. Product Registration Help us better support you by completing our online registration today! Connect to our Web site at Keep the original sales receipt, or a photocopy, in a safe place. Contact Garmin Contact Garmin if you have any questions while using your GDL 30A. In the USA contact Garmin Product Support by phone: (913) 397-8200 or (800) 800-1020, or go to In Europe, contact Garmin (Europe) Ltd. at +44 (0) 870.8501241 (outside the UK) or 0808 2380000 (within the UK). WARNING: See the Important Safety and Product Information guide in the product box for product warnings and other important information. Important Numbers For future reference, write down the important numbers associated with your GDL 30A. The serial number is located on the bottom of the unit. Serial number Unique ID numbers are associated with your GDL 30A. XM Satellite Radio™ uses these ID numbers to activate and deactivate your XM weather and XM audio. To locate the ID numbers on a GPSMAP® 3000 Series chartplotter, refer to the Main Menu section of the GDL 30A Owner’s Manual. To locate the ID numbers on a GPSMAP 4000 or 5000 Series chartplotter, select Configure > System > System Information. XM WX Weather™ ID XM Radio ID Packing List, Accessories, and Tools Needed Before installing your unit, check that your package includes the following items. If any parts are missing, contact your Garmin dealer immediately. Standard Package • GDL 30A unit • 7-pin power cable • Garmin Marine Network cable—6 ft. (1.8 m) • Documentation • Audio cable • Grommet • GA 32 Antenna . Surface-mount bracket . Pole-mount bracket . Under-deck mount bracket . Mounting hardware (screws and adhesive pads) Optional Accessories • GMS 10 network port expander • Garmin Marine Network cables (20 ft. and 40 ft.) Tools Needed (Not Included) • Drill and drill bits • Fasteners (to mount the GDL 30A) • Hole saw, 1 in. (surface-mount cable hole) • Screwdriver (surface-mount screws) • Center punch and hammer (to mark surface-mount pilot holes) • Countersink bit (when mounting on fiberglass) • Marine sealant (for certain mounting options) May 2008 190-00930-02 Rev. B Printed in Taiwan Unit Overview Power/data connector LED status indicator Mounting holes Weather cap Network port Antenna connector Audio connector CautIon: Always wear safety goggles, ear protection, and a dust mask when drilling, cutting, or sanding. When drilling or cutting, always check what is on the opposite side of the surface. Mounting the GDL 30A Mount the GDL 30A in a location that is dry and well ventilated. Avoid mounting the unit where it may become submerged or exposed to extreme temperatures above 158°F or below 5°F (above 70°C or below -15°C). Verify there is enough clearance to attach the cables to the unit. Make sure the Status LED is visible to view the blink codes. To mount the GDL 30A: 1. Using the unit as a template, mark the location of the mounting holes. If needed, additional holes can be drilled in the side mounting flanges. 2. Secure the GDL 30A using fasteners appropriate for the mounting surface. Connecting the Power Cable The power cable can be connected directly to the boat battery or through an open connector on the fuse block. To connect the power cable to a battery: 1. Connect the red wire to the positive (+) terminal of the battery. Do not remove the AGC/3AG 2.0 amp fuse holder from the red wire. 2. Connect the black wire to the negative (-) terminal of the battery. 3. Connect the power cable to the GDL 30A 7-pin connector labeled POWER. A fuse To GDL 30A Connecting to a Fuse Block 2. Connect the red wire to an open fuse holder in the fuse block. Make sure that the red wire is connected to the positive side of the fuse block. 3. Connect the black wire to the negative side of the fuse block. 4. Install a 2.0 A fuse in the fuse holder. 5. Connect the power cable to the GDL 30A 7-pin connector labeled POWER. 10–35 VDC Connecting to a Battery To connect the power cable to a fuse block: 1. Remove the AGC/3AG 2.0 A fuse holder from the red wire. Red Black Battery + Battery - GDL 30A Installation Instructions Connecting the GDL 30A to a Chartplotter Connect the GDL 30A to a chartplotter by using the Garmin Marine Network Cable (included). See the installation instructions for your chartplotter for more detailed information on setting up a Garmin Marine Network. Connecting to a GPSMAP 4000/5000 series chartplotter: • A GPSMAP 4000/5000 series chartplotter has three network connectors available. Connect the GDL 30A to any of these connectors. • If you have multiple chartplotters, connect the GDL 30A to an open connector on any one of the chartplotters. Connecting to a GPSMAP 3000 series chartplotter: • A GPSMAP 3000 series chartplotter has one network connector available. If you do not have any other Garmin Marin...