Stimmen - 4, Durchschnittliche Bewertung: 4.5
(
)
)
|
Anleitung Zusammenfassung
Disposable Lithium batteries have a much lower threshold for temperature with an estimated freezing range of below -30°C (-22°F). Wireless ranges can be impacted by a variety of factors such as extremely cold temperatures. Extreme cold may temporarily reduce the effective range between the sensor and the base station. If the unit's performance fails due to low temperature, the unit will resume proper functioning as the temperature rises to within the normal temperature range (i.e. no permanent damage will occur to the unit due to low temperatures). .... REMOTE SENSOR (THN132N) ALARM To set the alarm: 1. Press and hold ALARM for 2 seconds. 2. Press / to set hour / minute. 3. Press ALARM to confirm. indicates alarm is ON. To enable / disable the alarm: 1. Press ALARM to display alarm time. 2. Press ALARM again to turn alarm ON / OFF. To silence the alarm: • Press SNOOZE to silence it for 8 minutes. OR • Press any key except SNOOZE to turn the alarm off and activate it again after 24 hours. .. ............ 1. SNOOZE 2. ALARM: View alarm status; set alarm WEATHER FORECAST BACK VIEW This product forecasts the next 12 to 24 hours of weather within a 30-50 km (19-31 mile) radius based on barometric pressure trend readings. ................ ICON DESCRIPTION 1. LED indicator 1. Wall mount 2. Battery compartment 3. Battery door 4. Table stand 5. RESET 6. CHANNEL switch Clear SENSOR DATA TRANSMISSION Partially Cloudy The sensor reception icon in the remote sensor area shows the status. Cloudy ICON DESCRIPTION GETTING STARTED Main unit is searching for the sensor(s) BATTERIES Rainy Insert batteries before first use, matching the polarity (+ and -). Press RESET after each battery change. A channel has been found and sensor signal is being received NOTE The maximum operating altitude for weather forecast is 2500m (8202 ft). and “- - . -“ (Outdoor temperature area) The sensor cannot be found. Search for the sensor or check batteries TEMPERATURE To toggle temperature unit: Press °C / °F. To view outdoor sensors temperature readings: Press CHANNEL. To auto-scan between sensors: Press and hold CHANNEL for 2 seconds. Each sensor’s data is displayed for 3 seconds. To end auto-scan: Press CHANNEL or MEM. To toggle between current, minimum and maximum records for the selected sensor: Press MEM repeatedly. To clear the records: Press and hold MEM for 2 seconds. To search for a sensor: Simultaneously, press and hold MEM and CHANNEL for 2 seconds. NOTE If the sensor is still not found, check the batteries, obstructions, and remote unit location. indicates main unit batteries are low. NOTE Do not use rechargeable batteries. We recommend that you use alkaline batteries with this product for longer usage and lithium batteries in temperatures below freezing. 1: / : Increase / decrease setting; activate / deactivate clock reception signal 2: MODE: Change settings / display 3. CHANNEL: Switch remote sensor display 4. MEM: View current, maximum and minimum temperature / humidity 5. °C / °F: Select temperature unit 6. TEMP HI / LO : Change settings or enable / disable hi or lo temperature alarm for channel 1 7. RESET: Reset unit to default settings 8. Battery compartment CLOCK CLOCK RECEPTION This product is designed to synchronize its date and time automatically once it is within range of the WWVB-60 signal from the atomic clock in Fort Collins, Colorado. The clock collects the radio signals whenever it is within 3219 km (2000 miles) of a signal. REMOTE SENSOR The sensor collects temperature readings approx. every 40 seconds and sends them to the main unit. The main unit can collect data from up to 3 sensors. TEMPERATURE AND PRESSURE TREND SPECIFICATIONS The temperature and pressure trend icons are based on recent sensor readings. TYPE DESCRIPTION MAIN UNIT RISING STEADY FALLING L x W x H 130 x 55 x 112 mm (5.1 x 2.1 x 4.4 in) Weight 176 g (6.2 oz) without batteries °C / °F Temperature unit -5°C to 50°C (23°F to 122°F) Temperature range ICE WARNING Resolution 0.1°C (0.2°F) If the channel 1 sensor falls between 3°C to –2°C (37°F to 28°F), flashes to warn you that the temperature is approaching freezing. NOTE The warning will automatically stop if the temperature goes outside the ice-warning range. Clock frequency WWVB-60 Auto or disabled Synchronization 433 MHz Signal frequency Auto or manual (disabled) Clock Humidity range 25% - 95% Humidity resolution 1% Min / Max relative humidity and temperature Memory HI / LO TEMPERATURE ALARM An alert can be set to sound if the sensor set to channel 1 records above or below a temperature of your choice. To set alarm ON / OFF: 1. Press and hold TEMP HI / LO . 2. Use and to select high / low temperature alarm. Press TEMP HI / LO to confirm. 3. Press / to set alarm ON / OFF and press TEMP HI / LO to confirm. 4. If alarm has been activated, use and to select the temperature. 5. Press TEMP HI / LO to confirm. To silence the hi / lo temperature alarm: Press any key. The alarm resets automatically and will ...