Stimmen - 2, Durchschnittliche Bewertung: 3
(
)
)
|
Anleitung Zusammenfassung
. . . . . . . . Receiver Module . . . . . . . . . . . . Installing the Receiver . . . . . . . . . . . . . . Initial Sensor System Test. . . . . . . . . . . . . . . . . Sensor Module Features . . . . . . . . . . . . . . . . . . . Installing the Sensor Module . . . . . . . . . . . . . . . 10 Freeze Sensor Site Selection. . . . . . . . . . . . . . . . 13 Set Temperature Activation Threshold. . . . . . . . 14 Water Conservation Feature . . . . . . . . . . . . . . . . 15 Smart Bypass Feature. . . . . . . . . . . . . . . . . . . . . 16 Water Delay Feature . . . . . . . . . . . . . . . . . . . . . . 16 Introduction Signal Strength . . . . . . . . Battery Strength . . . . . . . . . . . . Dry Out Feature . . . . . . . . . . . . . . Fail Safe Feature. . . . . . . . . . . . . . . . . Turn Receiver Module Off and On . . . . . . . . . . 20 Set or Restore the Sensor Address Code . . . . . . 20 Sensor Module Battery Replacement. . . . . . . . . 21 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . 22 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 Warranty Information . . . . . . . . . . . . . . . . . . . . . 25 Electromagnetic Compatibility. . . . . . . . . . . . . . 26 The Toro Wireless RainSensor system, model TWRS for rain sensing and TWRFS for rain and freeze sensing, is a powerful water conservation and management irrigation system to actual environmental factors vital landscape. Without sensor input, the controller simply turns the sprinklers based on a routine irrigation schedule. Linking controller operation to real-eliminates unnecessary irrigation and dramatically reduces resource compromising the health and beauty of your landscape. And–it’s wireless. No cable to run or holes to drill. Simple installation and setup delivers reliable, intelligent sensor The wireless resistant and a sensor The receiver and connects 24 Vac power source or splices directly The sensor module range of the receiver sun/shade exposure can provide reliable communication Once activated by preset rain communicates to the receiver The receiver responds by placing the controller’s automatic watering schedule on common circuit to prevent sprinkler When watering is once again needed, the sensor system automatically resets, More than just an accurate rain switch, the landscape with the simple, yet sophisticated Water Conservation feature. Just choose the conservation level that corresponds to your landscape A dry-out period, adjusted for actual rainfall duration, system resets to effectively delay automatic watering until it is actually needed. Other standard features include a Smart BypassTM button that gives you manual control over the sensor system with a single touch, system status indicators to system is active and watering is on hold, watering delay to postpone 1 to 5 days, air temperature displayed for Rain/Freeze sensors and irrigation in case the sensor system is not performing properly. Getting The wireless operation. In minutes. All you will need If you have problems properly, refer to the Troubleshooting section on remedy does not seem to help, Toro Irrigation help line at 1-345-8676 for assistance. Here’s all there is to it: Step 1 Step 2 The receiver is installed and connected The sensor and receiver are tested at close to your irrigation system controller. range to verify operation. 3 The sensor is adjusted to the preferred rainfall activation level. The sensor is installed using the Quick ClipTM mounting bracket or pipe-mount adapter. The operating features are set to your preferences. Asensor installation site is chosen and the system is tested again to verify operation. Step 5 Step 4 Step 6 Step 3 Recei v er Module eatur es 1 – Setup Button – Aceses the 2 – Adjust Button – Scrols through system operating 3– Mast Antenna– Adjusts easily for best 4– Digital Display– High-resolution LCD screen reference for sensor system 5– Sensor Status Indicators– Illuminates when sensor system active and automatic watering is on is active but has been bypassed to enable 6– Smart BypassTM Button– Multi-functional use. Pressed to bypass sensor operation, allowing automatic resume. Switches the Water Delay feature on and off. 7– Water Conservation LEDs– Indicate the Water Conservation feature level selected (Minimum, Medium or Maximum) . 8– Hinged Cover–Opens downward for receiver control access. Closed position protects receiver when installed outdoors. 3 4 5 6 7 8 1 2 Installing Module Important: Installation electrical codes. The receiver module the controller that provides • The display screen is clearly • The connection cable can reach • The antenna will be unobstructed 1. Install one of the provided stainless steel intended receiver location. Leave a 1/8" Note: Use screw anchors if installing the receiver 2. Hang the receiver on the screw ensuring the keyhole onto the screw shaft. Back the screw out as necessary 3. Install a second screw through the lower tab to secure the 4. Route the connection cab...