Stimmen - 4, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
LEARN SENSOR TO AAA+TM CONTROL PANEL (CONT) The Temperature Sensor is designed to monitor the temperature of a specific area, whether that is the indoor temperature or outdoor temperature. It works in conjunction with the AAA+TM Control Panel, as well as other Skylink’s alarm system such as SC-001 or AD-433S etc. When the actual temperature exceeds the preset limit, the control panel will either alert you or alarm will be triggered. In this package, you should find the temperature sensor, 2 lithium batteries, an external measuring probe for measuring outdoor temperature and mounting accessories. External measuring 2 pcs Temperature probe 3.5 x 20 screws Sensor External (Batteries inside) dry contact cable Please follow the instructions below to set up the temperature sensor. 2. LEARN SENSOR TO AAA+TM CONTROL PANEL 4. PROGRAMMING In order for the sensor to communicate with the control panel properly, the sensor must be programmed to the control panel. Follow the brief instructions below or refer to the detail instructions from the AAA+TM User’s Instructions to program the sensor to the control panel. Before proceeding, please remove the battery isolator from the sensor. Step Keys Function Description Note 1 [PROG] [MPIN] Enter Programming mode Enter master password to programming mode 3 beeps for valid password. 1 long beep for invalid password. 2 [3] Select learn sensor After [3] is entered, some zone LEDs will programming flash once, or twice, some will be off. The zone LEDs represent whether that zone is already occupied by another sensor. **See Table A below. 3 [0] to [9] Select sensor location Refer to the diagram below to select the sensor location, which includes the zone and sensor number. After you have selected the zone, that zone LED will be on. 4 Activate the sensor by pressing the red “Panic” Activate sensor Once the sensor is activated, the signal will be transmitted to the Con- You will hear [Zone X Sensor Y Accepted], where X and Y are the zone and sensor button on the trol Panel which numbers you have temperature will be stored. selected. sensor. This row : Buttons for Sensor 1 Zone LED : Flash once This row : Buttons for Sensor 2 Zone LED : Flash twice ® SENSOR 1 SENSOR 2 Zone 1 Button [1] Button [6] Zone 2 Button [2] Button [7] Zone 3 Button [3] Button [8] Zone 4 Button [4] Button [9] Zone 5 Button [5] Button [0] Note: Each location is allowed to learn one sensor only. Learning a sensor to a location will clear the memory of the sensor previously learnt. ZONE LED DESCRIPTION Off Zone is not occupied by any sensor Flashes once This zone is occupied by sensor 1. Flashes twice This zone is occupied by sensor 2. Flashes once, then twice This zone is occupied by sensors 1 and 2. ** Table A: Zone LED status for learning sensors. 3. LEARN SENSOR TO SC-001, AA-433 AND AD-433S To program the temperature sensor to other Skylink’s receivers, such as SC-001, AA-433, AD-433S etc, please follow the instructions below: 1) Activate the programming mode of your Skylink’s receiver (refer to the owner’s instructions of your Skylink’s receiver) 2) To transmit the signal from the temperature sensor, press the red button (panic button) on the temperature sensor. 3) Follow the rest of the instructions from the Skylink’s receiver to complete the programming procedure. There are several things you need to program: 1) Clock 2) Upper temperature limit 3) Lower temperature limit 4) Set the temperature unit (Fahrenheit / Celsius) Clock The current time will be displayed when the “HOUR” or “MIN” button is pressed. To set the hour: 1. Press and hold the “HOUR” button. 2. Whiling holding on to the “HOUR” button, press “UP” or “DOWN” to select the hour. 3. Release all buttons after setting the hour. To set the minute: 1. Press and hold the “MIN” button. 2. Whiling holding on to the “MIN” button, press “UP” or “DOWN” to select the minute. 3. Release all buttons after setting the minute. Upper Temperature Limit When the actual temperature is above the upper temperature limit, the temperature sensor will send a signal to the control panel. To set the upper temperature limit: 1. Press and hold the “HI” button. 2. Whiling holding on to the “HI” button, press “UP” or “DOWN” to select the upper temperature limit. 3. Release all buttons after setting the upper temperature limit. Lower Temperature Limit When the actual temperature is below the lower temperature limit, the temperature sensor will send a signal to the control panel. To set the lower temperature limit: 1. Press and hold the “LO” button. 2. Whiling holding on to the “LO” button, press “UP” or “DOWN” to select the lower temperature limit. 3. Release all buttons after setting the lower temperature limit. Set the temperature unit (Fahrenheit / Celsius) The temperature sensor can operate and back coverRemove display temperature in Fahrenheit or Celsius. To select the desire unit, open the back cover you will see a jumper connector for “C/F” as shown below. To select Fahre...