Stimmen - 4, Durchschnittliche Bewertung: 4.3
(
)
)
|
Anleitung Zusammenfassung
The Side Panel Kit is not designed and handling parts for your protection. Proper installation is to support the countertop or cabinets, so it is important that the responsibility of the installer. they be fully supported prior to installing the kit. The kit may be used for either a left-hand or a right-hand opening. BEFORE YOU BEGIN -Readtheseinstructions completely and carefully. I M PO RTANT-Save these instructions for local inspector's use. IH PO RTANT-OBSERVECODES ALLGOVERNING AND ORDINANCES. PARTS SUPPLIED: Panel Toekick Fq End panel [] Toekick panel D Panel support bracket [] 2 -#8 x 3/4" wood screws [] 4 -#10 x 1" wood screws Panel @ !#BIS/4" Wood Screws @ (#1O) 1" Wood Screws 1/4" x 3/8" Machine Screws E] 4 -1/4" x 3/8" machine [] 4 -1/4" nuts screws Lack Washer 1/4" Nut Toggle Bait Screw [] D 4 -1/4" lock washers 2 -3/16" x 3" toggle bolt screws Panel Support @ [] 2 -3/16" toggles Bracket Flat Washer [] 6 -3/16" flat washers D Insta!lation Instructions NOT INCLUDED: 2 -Lag bolts of appropriate size for use when the floor is ceramic tile, quarry tile or similar material. TOOLS YOU WILL NEED: E] Phillips head screwdriver [] Drill and assorted drill bits Screwdriver [_ 7/16" socket, box-end or open-end wrench Drill and Assorted [Z] Heasuring tape Drill Bits [] Carpenters square El] Safety glasses D Gloves Safetg Glasses Carpenters Gloves Measuring Tape installation instructions The installation of the side panel requires the panel support bracket to be mounted to the underside of the countertop and the toekick panel to be mounted to the floor. If the panel is installed perpendicular to a wall, the side panel will also be fastened to the wall. The enclosure for the dishwasher must be at least 24" wide. The dimensions on the adjacent diagrams show locations of the screw holes for the toekick panel and the support bracket panel. Locating the screw holes as shown will provide the required 24" opening for the dishwasher. The toekick panel is mounted with its 1" flange against the floor. Similarly, the panel support bracket is mounted with its 1" flange against the underside of the countertop. STEP i ADJACENT CABINET SHOULD BE SQUARE AND PLUMB FOR GOOD DISHWASHER FIT Check cabinet for perpendicularity to the floor with a carpenter's square. If the cabinet is out of square, it may be necessary to make adjustments in the installation of this panel to ensure the dishwasher will fit properly in the opening. \ L Figure A STEP 2 LAY OUT MOUNTING HOLES FOR TOEKICK PANEL The rear-mounting hole must be 3ol/4"from the back of the opening and 23-1/2" from the opposite side. The front mounting hole must be 19" from the back of the opening and 23-1/2" from the opposite side. Mark these two screw hole locations and punch or drill an appropriate pilot hole. ,\ lJ T° Note: Measurements are to Center of Holes If the floor is ceramic tile, quarry tile or similar material, it wil! be necessary to drill clearance holes through the tile so lag bolts can be screwed into the sub-floor to securely fasten the toekick panel against the floor. STEP 3 LAY OUT MOUNTING HOLES FOR PANEL SUPPORT BRACKET In the same manner as above and using the same dimensions, lay out the hole locations on the underside of the countertop. Use a punch to create a pilot hole or drill a pilot hole. However, when drilling pilot holes be extremely careful. Do not drill holes a!l the wag through the countertop. Panel Support Not...
Dieses Handbuch ist für folgende Modelle:Standbacköfen - GPS5WW (265.68 kb)