Stimmen - 2, Durchschnittliche Bewertung: 4 ( )

Hersteller: Avanti Dateigröße: 2.26 mb Dateiname: g2002cw_-_g2003css_-_g2404cw_-_g2405css.pdf Unterrichtssprache:

. GAS VALVES In the event of operating faults in the gas valves, call the Service Department. NOTE: Oven bulb replacement is not covered by your guarantee. Do not use steam jet cleaners because the humidity could infiltrate into the appliance making it dangerous. . BURNERS AND GRIDS . These parts can be removed and cleaned with appropriate products. . After cleaning, the burners and their flame distributors must be well dried and correctly replaced. . It is very important to check that the burner flame distributor and the cap has been correctly positioned - failure to do so can cause serious problems. . In appliances with electric ignition keep the electrode clean so that the sparks always strike. . Note: To avoid damage to the electric ignition do not use it when the burners are not in place. CORRECT REPLACEMENT OF THE BURNERS It is very important to check that the burner flame spreader “F” and the cap “C” have been correctly positioned (see figs. 20 and 21). Failure to do so can cause serious problems. Figure 20 Figure 21 In appliances with electric ignition, check that the electrode “S” (fig. 20) is always clean to ensure trouble-free sparking. The ignition plug must be very carefully cleaned. . OVEN SHELF INSTALLATION AND REMOVAL The oven shelves are provided with a security block to prevent accidental extraction. They must be inserted operating as per figure 22. To pull them out remove shelf in the inverse order. Keep attention to insert the shelves cor- rectly (see side figure). Figure 22 24 . OVEN DOOR The internal glass of the oven door can be easily removed for cleaning by unscrewing the two lateral fixing screws (fig. 23). Figure 23 figure 24 . REMOVABLE STORAGE DRAWER The drawer (fig. 24) comes out like a normal drawer. To remove the drawer open and lift it. Do not store flammable material in the oven or in the bottom drawer. . REMOVING THE OVEN DOOR To facilitate oven cleaning, it is possible to remove the door. Please follow the instructions carefully: . REMOVING THE OVEN DOOR – The oven door can easily be removed as follows: – Open the door to the full extent (fig. 25). – Attach the retaining rings to the hooks on the left and right hinges (Fig. 25a) – Hold the door as shown in Fig. 25d. – Gently close the door and withdraw the lower hinge pins from their location (Fig.25b) – Withdraw the upper hinge pins from their location (Fig. 25c). – Reset the door on a soft surface. – To replace the door, repeat the above steps in reverse order. Figure 25 Figure 25a Figure 25b Figure 25c Figure 25d . REMOVABLE STORAGE DRAWER For cleaning, you can remove the drawer by pulling it out until the stop point and lifting it up. Never store any flammable material in the drawer. . REPLACING THE OVEN LIGHT Before any maintenance is started involving electrical parts of the appliance, it must be disconnected from the power supply. • Let the oven cavity and broil burner cool down. • Switch off the electric supply. • Remove the protective cover. • Unscrew and replace the bulb with a new one suitable for high temperature (200°F ~ 550°C) having the same specifications: 120V 60Hz, 15W, E14. • Replace the protective cover. NOTE: Oven bulb replacement is not covered by your guarantee. . LEVELING THE RANGE The range must be level to obtain proper operating. The four screws type leveling legs located on the corners at the bottom of range should be adjusted by turning them clockwise to make the range higher or counter-clockwise to lower the range until the range is level. Use a level on surface units to check the leveling of the range (Please see Fig.26). Figure 26 .ANTI-TIP BRACKET INSALLATION To reduce the risk of tipping the range by abnormal usage or improper door loading, the range mustbe secured by properly installing the anti-tip device packed with the appliance. •Place the anti-tip bracket on the floor as shown figure. Anti-tip bracket can be installed on eitherrightor left side. •Make the locations of 2 holes of ant-tip bracket on the floor. •Use a 5/16” masonry drillbit and insertplastic anchor. •Secure bracket to floor using screws supplied. •Slide appliance into position. NOTE:If range is relocated, the bracketmust be removed and installed in new location. 1.30" 5.69" 1.18" The contour line of backpanel of applianceInstall the anti-tip bracket either right or left side. Anti-tip BracketThe contour line of left panel of applianceThe contour line of right panel of applianceThe contour line of front panel of applianceMove the appliance to the final position. Anti-tip Bracket 26 PROBLEMS WITH YOUR GAS RANGE? You can solve many common appliance problems easily, saving you the cost of a possible service call. Try the suggestions below to see if you can solve the problem before calling the servicer. TROUBLESHOOTING GUIDE FIND YOUR PROBLEM HERE POSSIBLE CAUSE HOW TO FIX IT Surface burners do not light. Surface control has not been completely turned to the ON position. Push in and turn control to the ON position until bur...

Herunterladen

Geben Sie zwei Ziffern: