Stimmen - 1, Durchschnittliche Bewertung: 5
(
)
)
|
Anleitung Zusammenfassung
Accessories Hot soapy water: Soak and clean with a dish cloth or brush. Catalytic cooking compartment panels The catalytic cooking compartment panels are coated with self- cleaning enamel. The surfaces clean themselves while the oven is in operation. Larger splashes will only be removed after the oven has been used several times. The rear and side walls are covered with catalytic panelling. Never clean these surfaces with oven cleaner. Slight discolouration of the enamel does not affect self-cleaning. Removing and fitting the appliance door You can remove the appliance door to clean it more thoroughly. Removing the appliance door : Risk of injury! Whenever the hinges are not locked, they snap shut with great force. When removing the oven door, ensure that the locking pins are fully inserted into the holes in the hinges. 1. Open the oven door fully. 2. Lock both hinges on the left and right using a locking pin (a) . Note: The locking pins must be fully inserted into the holes in the hinges. 3. Grip the oven door on either side with both hands and close the oven door by approx. 30° (b) . 4. Raise the oven door slightly and pull it out. Note: Do not fully close the oven door. The hinges may become bent and the enamel may be damaged. Fitting the appliance door 1. Grip the oven door on either side with both hands. 2. Slide the hinges into the slots in the oven (a) . Note: The notch below the hinges must engage into the frame of the oven (b) . 3. Lower the door downwards. 4. Remove the locking pins. : Risk of injury! If the oven door falls out accidentally or a hinge snaps shut, do not reach into the hinge. Call after- sales service. Removing and inserting the hook-in racks You can remove the hook-in racks for easier cleaning. Removing the hook- in racks 1. Unscrew the right and left-hand screws on the hook-in rack. 2. Remove the hook- in rack. Inserting the hook- in rack 1. Hold the hook-in rack in front of the drill holes in the side panel. 2. Screw in the hook-in rack tight again using the screws. Troubleshooting Malfunctions often have simple explanations. Refer to the table before calling the after- sales service, as you may be able to remedy the fault yourself. : Risk of injury! Incorrect repairs may cause serious hazards. Repairs to the appliance may only be performed by a qualified technician. If repairs are required, contact the after- sales service. Fault table Fault Possible cause Remedy/ information The appliance is not functioning. Faulty fuse Look in the fuse box and check that the fuse is in working order. Power cut Check whether the kitchen light works. 0 and zeros flash in the display. Power cut Reset the clock. The oven light has failed. Faulty oven light Change the oven light bulb, (see section "Replacing oven light" ) The gas burner does not ignite. Power cut or damp ignition plugs Light the gas burner with a gas lighter or a match. The oven does not heat up. Faulty fuse. Check the fuse and replace if necessary. The function selector has not been set. Set the function selector. All dishes prepared in the oven burn within a short period of time. Faulty thermostat Call the after-sales service. The door panel steams up when the oven is hot. Normal occurrence; caused by the difference in temperature. Not possible; this has no effect on oven performance. Error messages If an error message with “ appears, press the 0 button. The message disappears. A time function that has been set is cleared. If the error message does not disappear, please contact the after-sales service. You can take remedial action yourself if the following error message is displayed. Error message Possible cause Remedy/ information “‹ ‚‚ A button was depressed for too long or is covered up. Press all buttons individually. Check whether any buttons are jammed, covered up or soiled. : Risk of electric shock! Incorrect repairs are dangerous. Repairs may only be carried out by one of our trained after-sales engineers. Replacing the oven light bulb If the bulb in the oven light fails, it must be replaced. Replacement heat-resistant bulbs can be obtained from the after- sales service or from specialist retailers. Please supply your appliance's E number and FD number. Do not use any other type of bulb. : Risk of electric shock! When replacing the cooking compartment bulb, the bulb socket contacts are live. Before replacing the bulb, unplug the appliance from the mains or switch off the circuit breaker in the fuse box. 1. Switch off the circuit breaker or unplug the mains plug. 2. Open the appliance door. 3. Place a tea towel in the cold cooking compartment to prevent damage. 4. Unscrew the glass cover from the defective oven light bulb inside the cooking compartment. 5. Replace the oven light bulb with a bulb of the same type. Voltage: 230 V; Power: 25 W; Thread: E14; Temperature resistance: 300° C 6. Screw the glass cover for the oven light back on. 7. Remove the tea towel and switch the circuit breaker back on or plug in the mains ...