Stimmen - 2, Durchschnittliche Bewertung: 3.5
(
)
)
|
Anleitung Zusammenfassung
When used with a flexible hose, the connector on the wall should be between 800 mm to 850 mm above the floor and in the region outside the width of the appliance to a distance of 250 mm. This should be accessible with the appliance installed. g When protecting a wall with non-combustible material it must be at least 150 mm high. Installation Instructions Standards Requirements Australian and New Zealand Gas Installation Standards (AS5601, NZS 5261) require a cooktop to be installed so that the surface temperature of any nearby combustible surface will not exceed 65oC above ambient. Typically this is achieved by: A Having the cooktop spaced away from the wall (see “Clearances” for dimensions) [Dimension c and d] OR B by protecting the wall, to at least 150 mm high [Dimension g] along it’s length, with non-combustible surface materials, such as: -5 mm thick ceramic tiles alone are adequate. -Tempered glass or sheetmetal (min. 0.4 mm thick) is acceptable when used in front of a fire resistant material. - Fisher & Paykel Splashback (not available in Australia): This is stainless steel with a 10 mm air gap to the wall. When used with a 10 mm gap behind the product to the front of the splashback. (Only with SB90 series and SB1216 splashbacks.) These products meet the Standards requirements when installed to the dimensions in these Instructions. (They have been tested by an Independent Testing Lab). Clamping Down the Cooktop This cooktop is supplied with fastening clamps that will cope with a bench thickness of 20-50 mm. For benchtops thicker than 50 mm, recess the underside to a thickness of 20-50 mm. 20 mm 50 mm recessed to 50 mm Gas Supply Connection This cooktop is supplied set up for Natural Gas but is suitable for installation with either Natural Gas or LPG. Refer to relevant table for pressures and appropriate orifice sizes. CG602, CG902 series Gas connection to the product MUST use the elbow supplied. The regulator will not seal if installed without it. Ensure the blue washer (supplied) is located between the elbow (supplied) and product inlet as below. Failure to use this washer will cause the product to leak. Tighten the floating nut to firm finger tight, plus an additional 1/4 turn (90o). Blue washer Elbow (1/2” BSP male) Gas Inlet (1/2” BSP internal thread) CG913 series After installation, make sure all connections are gas tight. A duplicate data plate enclosed inside the accessories pack should be placed on an accessible surface adjacent to the cooktop. Flexible Hoses Flexible hose assemblies should be AS/NZS 1869 Class B or Class D certified. Flexible hoses should not be exposed to temperatures exceeding their certified value. They should not touch hot surfaces on the cooktop or neighbouring products. Flexible hoses should not be subject to abrasion, kinking or permanent deformation. Installation Instructions Natural Gas For Natural Gas usage the gas supply is connected to the regulator which is supplied loose with a built in test point - 1kPa (4” WG) and the inlet connection of 1/2 “ B.S.P. (male thread). Do not over tighten. The test point pressure should be preset to 1.0 kPa with the wok and semi - rapid burners operating at maximum. LP Gas For LPG usage the gas supply for the appliance must be regulated to a pressure of 2.75kPa (11” WG). See ‘Conversion to a different gas type’ . Gas Supply Connection Check The connection point shall be accessible with the appliance installed. To enable the gas supply to be readily shut off, the gas supply must be connected with an isolating valve close to the product. After installation and making all connections check thoroughly for possible leaks. 1 Turn all control knobs on the unit to “off” position. 2 Open the valve on the gas supply. 3 Using a suitable leak detection fluid solution (e.g. Rocol) check each gas connection one at a time by brushing the solution over the connection. 4 The presence of bubbles will indicate a leak. Tighten the fitting and recheck for leaks. Ensure the washer (supplied) is located between elbow and product gas inlet. 5 Turn on each gas valve and light each burner. 6 Check for a clear blue flame without yellow tipping. If burners show any abnormalities, check that they are located and assembled properly. Check correct orifices are installed. CG913TM only The operation of the appliance, including the ignition system, must be tested before installation is complete. If after following the instructions given, satisfactory performance cannot be obtained, contact the local gas authority or your local Approved Service Agent for advice and assistance. Conversion to Different Gas Type Burners can be used with NG or LPG, provided that the orifices appropriate for the gas supply are installed. To change the orifices, you will need a 7 mm box spanner (and a 10 mm ring spanner for CG913TM). 1 Turn off the main electrical supply. WARNING! Electrical Shock Hazard. Disconnect product from main power supply before continuing. 2 Ensure all gas valv...