Stimmen - 0, Durchschnittliche Bewertung: 0
(
)
)
|
Anleitung Zusammenfassung
The connection, maintenance and setting of the pressure regulator must be carried out by an approved gas fitter. If you do not know the pressure of your local gas supply, ask your gas supplier. For your safety This appliance is adjusted to operate on LPG only. Faults in the gas installation/ smell of gas If you notice a smell of gas or faults in the gas installation, you must ¦ immediately shut off the gas supply and/ or close the gas cylinder valve ¦ immediately extinguish all naked flames and cigarettes ¦ switch off electrical appliances and lights ¦ open windows and ventilate the room ¦ call the aftersales service or the gas supplier Burn back Fire in burner tube or chamber In the event of a burn-back, where the flame burns back to the jet, immediately turn off the gas supply at the control valve on the panel. After ensuring the flame is extinguished, re-light the appliance in the normal manner. Should the appliance again burn back, close the control valve and call a service technician. Do not use the appliance again until the service technician has declared that it is safe to do so. Gas- pressure regulator This appliance requires an operating pressure of 2,8 kPa at the appliance. A suitable LPG regulator that coplies with the requirements of SANS 1237 must be installed. Important information for the user This appliance may only be installed by a registeres LP Gas installer. All registered installers are issued with a card carrying their registration number. Ask to be shown the card before allowing the installation work to be shown the card before allowing the installation work to commence and make a note of the installer QCC number. Upon completion of the installation, the installer is required to explain the operational details of the appliance together with the safety instructions. You should only sign for acceptance of the installation and be provided with a copletion certificate. You should only sign for acceptance of the installation when the installation is completed to your satisfaction. Note that your invoice is required in the event that you wish make a quarantee claim. Important information for the installer This appliance may only be installed by a registered LP Gas installer registered with the Liquefied Petroleum Gas Association of Southern Africa. The appliance must be installed in accordance with the requirements of SANS 10087-1 and any fire department regulations and/or local bylaws applicable to the area. If in doubt check with the relevant authority before undertaking the installation. Upon completion of the installation you are required to fully explain and demonstrate to the user the operational details and safety practices applicable to the appliance and the installation. Moving the appliance by the gas line or door handle Do not move the appliance while holding the gas line; the gas pipe could be damaged. There is a risk of a gas leak! Do not move the appliance while holding it by the door handle. The door hinges and door handle could be damaged. Electrical connection Caution! ¦ Have the appliance set up by your after- sales service. A 16 A fuse is required for connection. The appliance is designed for operation at 220-240 V. ¦ If the electricity supply drops below 180 V, the electrical ignition system does not work. ¦ Any damage arising from the appliance being connected incorrectly will invalidate the guarantee. ¦ If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard. For the after- sales service Caution! ¦ The appliance must be connected in accordance with the data on the rating plate. ¦ Only connect the appliance to an electrical connection that meets the applicable provisions. The socket must be easily accessible so that you can disconnect the appliance from the electricity supply if necessary. ¦ Please ensure the availability of a multi- pin disconnecting system. ¦ Never use extension cables or multiple plugs. ¦ For safety reasons, this appliance must only be connected to an earthed connection. If the safety earth terminal does not comply with regulations, safety against electrical hazards is not guaranteed. ¦ You must use a H 05 W-F type cable or equivalent for the appliance connection. Levelling the cooker Always place the cooker directly on the floor. 1. Pull out the plinth drawer and lift it up and out. There are adjustable feet at the front and rear on the inside of the plinth. 2. Use an Allen key to raise or lower the adjustable feet as necessary until the cooker is level ( picture A) . 3. Push the plinth drawer back in ( picture B) . Setting up the appliance ¦ The appliance must be set up directly on the kitchen floor and in line with the specified dimensions. The appliance must not be set up on any other object. ¦ The distance between the top edge of the oven and the bottom edge of the extractor hood must meet the requirements of the extractor hood manufacturer. ¦ Ensure tha...
Dieses Handbuch ist für folgende Modelle:Standbacköfen - HGV745356Z/02 (2.45 mb)
Standbacköfen - HGV745356Z/03 (2.45 mb)