Stimmen - 2, Durchschnittliche Bewertung: 4 ( )

Hersteller: DCS Dateigröße: 827.36 kb Dateiname: Unterrichtssprache:

You know you have a Class ABC extinguisher, and you already know how to operate it. 2. The fire is small and contained in the area where it started. 3. The fire department is being called. 4. You can fight the fire with your back to an exit. WARNING! Do not place items of interest to children on racks or appliance. Children could be seriously injured if they should climb onto or into the appliance to reach these items. WARNING! Do not place combustible material (paper, cloth, plastic, etc.) on the rack. PLEASE RETAIN THIS MANUAL FOR FUTURE REFERENCE. 1 TABLE OF CONTENTS SPECIFICATIONS 3 WALL MOUNT LOW BACKGUARD INSTALLATION 3 WALL MOUNT FULL BACKGUARD INSTALLATION 4-5 SPECIFICATIONS B A 8-3/4 " 12 " B A 1-5/16 " 1-5/16 " MODEL A BGS-1230 BGS-3030 B BGS-1236 BGS-3036 BGS-1248 BGS-3048 29-7/8" -- - - - 2 - - - 2 2 1 RACK (16-5/8") QTY. RACK (13-5/8") QTY. 29-7/8" 35-7/8" 35-7/8" 47-7/8" 47-7/8" 10-1/8" 10-1/8" 28-1/8" 28-1/8" 10-1/8" 28-1/8" WALL MOUNT LOW BACKGUARD INSTALLATION 1. Locate and level range per installation instructions. 2. After unpacking all backguard system parts, locate the Back Section 1/8” above and centered over the Island Trim attached to the range.* Secure Back Section to wall with the appropriate fasteners (not supplied)(fig. 01). *After 1/8” is located, slots in back section may be used to adjust spacing between range island trim and backguard for a flush fit. 3. Secure Front Section of backguard to Back Section with #8 self-tapping sheet metal screws supplied (fig. 02). Back Section Island Trim Slots to choose desired spacing between Range Island Trim and Backguard. 16”for30” 36”for36/48” Back Section Front Section # 8 Self-tapping sheet metal screws Fig.01 Fig.02 3 WALL MOUNT FULL BACKGUARD INSTALLATION RECOMMENDED INSTALLATION ORDER: 1) VENT HOOD 2)BACKGUARD SYSTEM 3) RANGE 1. Locate and level range per installation instructions. 2. After unpacking all backguard system parts, locate the Back Section 1/8” (see fig. 03) above and centered over the Island Trim attached to the range.* Secure Back Section to wall with the appropriate fasteners (not supplied) to anchors or wood stud (fig. 03). WARNING: The Back Section must be securely fastened to the wall. Failure to do so could cause damage or personal injury if the Backguard was to pull free from wall when racks are loaded. The maximum weight placed on each rack should be 10 lbs. *After 1/8” is located, slots in back section may be used to adjust spacing between range island trim and backguard for a flush fit. 3. Attach rod, end caps and center stanchion to Front Section of backguard with #10 machine screws supplied (fig. 04). 4. Bend wedge-shaped tabs down on top of the front section approximately 3/16”. When mounting the front section, insure that these tabs engage the mating holes in the top of the rear section (see fig. 05, page 4). 5. Secure Front Section of backguard to Back Section with #8 self-tapping sheet metal screws supplied (fig. 05, page 4). 6. Attach racks to...

Herunterladen

Geben Sie zwei Ziffern: