Stimmen - 3, Durchschnittliche Bewertung: 3.3
(
)
)
|
Anleitung Zusammenfassung
In the event of a power outage, you can use this heater as your primary heat source. WARNING: A qualified service person must install heater. Follow all local codes. WARNING: Never install the heater • in a bedroom or bathroom • in a recreational vehicle • where curtains, furniture, clothing or other flammable objects are less than 42 inches from the front, top or sides of the heater • in high traffic areas • in windy or drafty areas CAUTION: This heater creates warm air currents. These currents move heat to wall surfaces next to heater. Installing heater next to vinyl or cloth wall coverings or operating heater where impurities (such as, but not limited to, tobacco smoke, aromatic candles, cleaning fluids, oilorkerosenelamps,etc.)in the air exist, may discolor walls or cause odors. in rooms without enough ventilation air may cause mildew to form from too much moisture. See Air for Combustion and Ventilation, page 5. CHECK GAS TYPE Use the correct gas type (natural or propane/LP) for your unit. If your stove heater gas type is different from your house gas type, do not install heater. Call dealer where you bought heater for proper type heater. WARNING: This appliance is equipped for (natural or pro- pane/LP) gas. Field conversion is not permitted. CLEARANCES TO COMBUSTIBLES (Vent-Free Operation Only) WARNING: Maintain the minimum clearances.Ifyoucan, provide greater clearancesfrom floor, ceiling and adjoining side and back walls. Carefully follow the instructions below. This stove is a freestanding unit designed to set directly on the floor. DO NOT place stove directly on carpeting, vinyl tile or any combustible material other than wood. The stove must be set on a metal or wood panel extending the full width and depth of the stove for these floor coverings. Important: You must maintain minimum wall and ceiling clearances during installation. The minimum clearances are shown in Figure 5, page 9. Measure from outermost point of stove top. Minimum Wall and Ceiling Clearances (see Figure 5, page 9) A. Clearances from outermost point of stove top to any combustible side wall should not be less than 12 inches. B. Clearances from outermost point of stove top to any combustible back wall should not be less than 6 inches (includes corner installations). C. Clearances from the stove top to the ceiling should not be less than 48 inches. 111487-01E INSTALLATION CONNECTING TO GAS SUPPLY Continued Front View 12" Minimum 12" Minimum 48" Minimum Ceiling Side Wall Side Wall Back Wall 6 " Minimum 12 " 12 " Minimum Minimum Side Wall Side Wall Front of Stove Unit Top View Corner Wall Floor Wall 6 " Minimum 6 " Minimum Front of Stove Unit Back Wall Front of Stove Unit Side View Figure 5 - Minimum Clearance to Walls and Ceiling (Stove May Vary Depending on Model) WARNING: This appliance requires a 1/2" NPT (National Pipe Thread) inlet connection to the pressure regulator. WARNING:Aqualified service personmustconnectheatertogas supply. Follow all local codes. CAUTION: Never connect propane/LPheaterdirectlytothe propane/LP supply. This heater requires an external regulator (not supplied). Install the external regulator between the heater and propane/LP supply. WARNING: Never connect naturalgasheatertoprivate(nonutility) gas wells. This gas is commonly known as wellhead gas. Installation Items Needed Before installing heater, make sure you have the items listed below. • external regulator [propane/LP only] (supplied by installer) • piping to stove location (check local codes) • sealant (resistant to propane/LP gas) • equipment shutoff valve * • test gauge connection * • sediment trap • tee joint • pipe wrench * A CSA design-certified equipment shutoff valve with 1/8" NPT tap is an acceptable alternative to test gauge connection. Purchase the optional CSA design-certified equipment shutoff valve from your dealer. See Accessories, page 19. The gas inlet connection for the stove heater is located on the lower right-hand side of the stove when viewed from the front of the unit. The gas connection can be made either through the bottom right side or through the lower back opening as illustrated in Figure 6, page 10. Make sure gas log heater is secured to the stove cavity assembly. 111487-01E INSTALLATION Continued For propane/LP units, the installer must supply an external regulator. The external regulator will reduce incoming gas pressure. You must reduce incoming gas pressure to between 11 and 14 inches of water. If you do not reduce incoming gas pressure, heater regulator damage could occur. Install external regulator with the vent pointing down as shown in Figure 7. Pointing the vent down protects it from freezing rain or sleet. CAUTION: For propane/LP units, use only new, black iron or steel pipe. Internally-tinned copper tubing may be used in certain areas. Check your local codes. Use pipe of 1/2" diameter or greater to allow proper gas volume to heater. If pipe is too small, undue loss of volume w...
Dieses Handbuch ist für folgende Modelle:Standbacköfen - CSBNT (1.04 mb)
Standbacköfen - CSPBNT (1.04 mb)
Standbacköfen - CSPBPT (1.04 mb)
Standbacköfen - CSPINT (1.04 mb)