Stimmen - 2, Durchschnittliche Bewertung: 3.5
(
)
)
|
Anleitung Zusammenfassung
This will cause rust and corrosion and it is totally the operator’s fault. Usually after the coal dries for three or four days, depending on conditions, it will flow very well and feed properly. Feed rate will be the same as with dry coal. wet Coal Always Empty hopper Never use gasoline, gasoline-type lantern fuel, kerosene, charcoal lighter fluid, or similar liquids to start or “freshen up” a fire in this heater. keep all such liquids well away from the heater while it is in use. 5 This remarkable design by Harman features the Verti-flow Direct Vent Stoker System. This unique, high efficiency unit uses only outside air for combustion. Micro-processor controls provide for an automatic wide range of heat output from 7,000 to 75,000 BTU . With a big 93 pound hopper capacity, this unit can burn on high approximately 16 hours or extend for over 96 hours on low. A Room Sensor connected to the micro-processor automatically adjusts the feed rate to compensate for changes in temperature. The ash pan is large enough to hold the ash from one hopper full of coal at any setting. The DV C 500 is the most advanced coal stove ever put into production. However, there are places where it should not be installed. If the end of the flue pipe is: 1. Less than 8 feet from an air intake. 2. On the side of the house where a window is left open for sleeping. 3. Less than 5 feet from a door. 4. Less than 7 feet above and 3 feet away from a public walkway. 5. Less than 3 feet above ground level. 6. Between two buildings less than 10 feet apart. It is recommended that the end of the flue pipe terminates at least 12 inches away from the side of the building in order to minimize any fly ash build-up. Mobile home installations should be done in accordance with the Manufactured Home and Safety Standard (HUD ), CFR 3280, Part 24. DAMP COAL SHOULD NOT BE LEFT IN THE HOPPER OF A COLD STOVE. Introduction 6 1. Install the hopper latch as shown at left. 2. Install 3 firebricks on the cast iron angle behind the grate as shown. 3. Cement in grates as shown below. This may already be done at the factory. 3 Bricks Grate Inserts fig. 3 Assembly 7 4 GLASS RETAINER CLIPS 4 GLASS RETAINER BOLTS GLASS GLASS GASKET DOORHINGE PINS PAW BOLT viewing glass The glass in your Harman stove is a special ceramic glass. • Do not abuse the glass by striking or slamming the door. • Never burn the appliance if the door glass is cracked or broken. • Replace only with Harman supplied glass. Soot and/or fly-ash may accumulate on the viewing glass, and will ocassionally need to be cleaned. Clean the glass with a soft cloth and mild glass cleaner. Do not spray cleaner on hot glass, and avoid the use of abrasive cleaners. Glass replacement Carefully remove all remaining glass and gasket materials prior to replacing the glass. Lay the door face down on a flat surface. Remove the glass retainers and screws. Apply the gasket material to the face of the new glass. Lay the glass into the door, making sure that the glass is contained within the channels and raised areas of the door itself. Lay the glass retainers into position and install the screws. Tighten each screw evenly to avoid making any stress points. BRASS HANDLE HANDLE BOLT WOOD HANDLE SET SCREW 4 GLASS RETAINER CLIPS 4 GLASS RETAINER BOLTS GLASS GLASS GASKET DOORHINGE PINS PAW BOLT viewing glass The glass in your Harman stove is a special ceramic glass. • Do not abuse the glass by striking or slamming the door. • Never burn the appliance if the door glass is cracked or broken. • Replace only with Harman supplied glass. Soot and/or fly-ash may accumulate on the viewing glass, and will ocassionally need to be cleaned. Clean the glass with a soft cloth and mild glass cleaner. Do not spray cleaner on hot glass, and avoid the use of abrasive cleaners. Glass replacement Carefully remove all remaining glass and gasket materials prior to replacing the glass. Lay the door face down on a flat surface. Remove the glass retainers and screws. Apply the gasket material to the face of the new glass. Lay the glass into the door, making sure that the glass is contained within the channels and raised areas of the door itself. Lay the glass retainers into position and install the screws. Tighten each screw evenly to avoid making any stress points. BRASS HANDLE HANDLE BOLT WOOD HANDLE SET SCREW Installation fig. 6 fig. 7 dO NOT INSTAll A FluE dAmPEr IN ThE EXhAuST vENTINg SYSTEm OF ThIS uNIT dO NOT CONNECT ThIS uNIT TO A ChImNEY FluE SErvINg ANOThEr APPlIANCE. INSTAll vENT AT ClEArANCES SPECIFIEd bY ThE mANuFACTurEr Tips On Installation Before the positioning of the unit can be decided a few questions should be considered? 1. Can the unit be vented properly and installed safely? 2. Will exhaust be vented where fumes can build up or be drawn into lower levels of the structure 3. Will fumes and fly ash affect the exterior of the structure or surrounding structures? 4. Are there any local regulations governing the use and placement of the...